Code :

Code: CC159, CC15A
Description: ROM contents error upon startup (DSC1), ROM contents error upon startup (DSC2). A fault is detected in a sequence of ROM contents check of the DSC board during starting.
Causes: • DSC board/1 (DSCB/1; SC-508) • DSC board/2 (DSCB/2; SC-508)
Remedy: 1 Check DSCB/1 or DSCB/2 connector for proper connection and correct as necessary. 2 Turn OFF the main power switch, disconnect and then connect the power cord. Wait for 10 sec. or more after connect the power cord, and turn ON the main power switch. 3 Rewrite the firmware. 4 Replace DSCB/1 or DSCB/2

Code: CC15B
Description: Finisher ROM error (SD) <When FS-534+SD-511 is installed, When FS-535+SD-512 is installed> Data of flash ROM of the saddle unit is determined to be faulty when the main power switch is turned ON.
Causes: SD drive board (SDDB)
Remedy: 1 Turn OFF the main power switch, disconnect and then connect the power cord. Wait for 10 sec. or more after connect the power cord, and turn ON the main power switch. 2 Rewrite the firmware. 3 Replace SDDB(SD-511/SD-512)

Code: CC163
Description: ROM contents error (PRT) The wrong model of firmware is detected in the engine during the initial connection to the engine is being checked.
Causes: • SSD board (SSDB) • Printer control board (PRCB)
Remedy: 1 Rewrite the firmware. 2 Replace PRCB 1. Turn OFF the main power switch and replace the current PRCB with a new one. 2. Update the PRCB firmware. 3. After completing the firmware update, turn OFF and ON the main power switch and check to see that warm-up is started. 4. When the trouble cannot be solved, reinstall the removed PRCB to the original board. NOTE • When taking the above steps, check whether PRCB is defective or not without replacing the SSDB. 3 If the above actions do not solve the problem, contact KM.

Code: CC164
Description: ROM contents error (MSC) • The wrong model of firmware is detected in the MFP board when the main power switch is turned ON. • The machine type information (Machine, Type) registered to the machine differs from the actual machine type.
Causes: • Printer control board (PRCB) • MFP board (MFPB)
Remedy: 1 Check the ROM version. 2 Check the machine type information registered and reenter as necessary. For details the machine information, see “J.2.4 Entering the machine type information”. 3 Rewrite the firmware. 4 Replace the corresponding board. 5 When not reviving even if the above-mentioned procedure is done, contact the responsible people of KM.

Code: CC165
Description: ROM contents error (DF) When the power is turned ON, DF control board or firmware error is detected.
Causes: DF control board (DFCB)
Remedy: 1 Turn OFF the main power switch, disconnect and then connect the power cord. Wait for 10 sec. or more after connect the power cord, and turn ON the main power switch. 2 Rewrite the firmware. 3 Replace DFCB

Code: CC166
Description: ROM error (i-Option) • In the environment in which the searchable PDF function or the web browser function is being used, firmware is not installed in the hard disk that has replaced an old one. • In the environment in which the searchable PDF function or the web browser function is being used, firmware is not installed after Physical Format was performed of the hard disk.
Causes: Hard disk • OCR (Character Recognition): Searchable PDF function • Web browser function
Remedy: 1 Rewrite the firmware. 2 Replace the hard disk.

Code: CC170 ... CC186
Description: Dynamic link error during starting (AP0) Dynamic link error during starting (AP1) Dynamic link error during starting (AP2) Dynamic link error during starting (AP3) Dynamic link error during starting (AP4) Dynamic link error during starting (LDR) Dynamic link error during starting (IBR) Dynamic link error during starting (IID) Dynamic link error during starting (IPF) Dynamic link error during starting (IMY) Dynamic link error during starting (SPF) Dynamic link error during starting (OAP) Detection timing A dynamic link error occurs in the program on the MFP board due to an insufficient memory space available, a ROM fault, or other reason when the main power switch is turned ON.
Causes: MFP board (MFPB)
Remedy: 1 If the malfunction code "CC172" has occurred, access [Service Mode] -> [System 2] -> [Image Controller Setting] and check to see if "Controller 1," "Controller 2," "Controller 3," or "Others" is set for [Image Controller Setting]. If any of these is set, select "Controller 0." 2 If the malfunction code "CC180" has occurred, check to install the appropriate loadable device driver for an authentication unit which is installed to the MFP. When the appropriate loadable device driver is not installed, reinstall the appropriate loadable device driver. 3 Replace MFPB 4 When not reviving even if the above-mentioned procedure is done, contact the responsible people of KM.

Code: CC190
Description: Outline font load error An error occurred while loading the outline font.
Causes: • MFP board (MFPB) • Hard disk
Remedy: 1 Check the connector between the hard disk-MFPB PJ11 for proper connection and correct as necessary. 2 Format the hard disk. 3 Replace the hard disk. 4 Replace MFPB