Thương hiệu phân phối chính hãng
Giỏ hàng

Mã lỗi Konica-Minolta bizhub C227 — Trang 18/31

Code: C2A14

Description: Drum unit/K new release failure. The status with the new unit is not cleared after the new imaging unit or new drum unit is set.
Causes: • Imaging unit/Y,M,C • Drum unit/K • MFP board (MFPB)
Remedy: 1. Clean the connection between the imaging unit or drum unit/K and the machine if dirty. 2. Reinstall the imaging unit. 3. Reinstall the drum unit/K. 4. Check the connector between the imaging unit/Y,M,C-relay CN162,CN163,CN164-relay CN15-MFPB CN18E for proper connection and correct as necessary. 5. Check the connector between the drum unit/K-relay CN14-MFPB CN15E for proper connection and correct as necessary. 6. Replace the the corresponding imaging unit. 7. Replace the drum unit/K. 8. Replace MFPB. NOTICE • Link to the layout drawings for related parts by each trouble code (S.44. C2552, C2559, C2561, C2A11) • Link to the layout drawings for related parts by each trouble code (S.46. C2554, C255A, C2562, C2A12) • Link to the layout drawings for related parts by each trouble code (S.48. C2556, C255B, C2563, C2A13) • Link to the layout drawings for related parts by each trouble code (S.51. C2A14)

Code: C3201

Description: Fusing motor failure to turn. The motor lock signal remains HIGH for a predetermined continuous period of time while the motor is turning.
Causes: • Fusing motor (M3) • MFP board (MFPB)
Remedy: 1. Check the connector between M3-MFPB CN11E for proper connection and correct as necessary. 2. Check the loading status of the fusing unit drive, and correct the error as necessary. 3. M3 operation check • Control signal: MFPB CN11E-11 (REM), MFPB CN11E-14 (FGP) • Location of electrical component: 3-C 4. Replace M3. 5. MFPB F23E conduction check 6. Replace MFPB. NOTICE • Link to the wiring diagram (N.1. bizhub C287/C227) • Link to the layout drawings for related parts by each trouble code (S.52. C3201, C3202)

Code: C3202

Description: Fusing motor turning at abnormal timing.The motor lock signal remains LOW for a predetermined continuous period of time while the motor remains stationary.
Causes: • Fusing motor (M3) • MFP board (MFPB)
Remedy: 1. Check the connector between M3-MFPB CN11E for proper connection and correct as necessary. 2. Check the loading status of the fusing unit drive, and correct the error as necessary. 3. M3 operation check • Control signal: MFPB CN11E-11 (REM), MFPB CN11E-14 (FGP) • Location of electrical component: 3-C 4. Replace M3. 5. MFPB F23E conduction check 6. Replace MFPB. NOTICE • Link to the wiring diagram (N.1. bizhub C287/C227) • Link to the layout drawings for related parts by each trouble code (S.52. C3201, C3202)

Code: C3302

Description: Paper cooling fan failure to turn. The fan lock signal remains HIGH for a predetermined continuous period of time while the fan is turning.
Causes: • Paper cooling fan (FM8) • MFP board (MFPB)
Remedy: 1. Check the connector between FM8-relay CN27-MFPB CN12E for proper connection and correct as necessary. 2. Check the fan for possible overload and correct as necessary. 3. FM8 operation check • Control signal: MFPB CN12E-1 (REM), MFPB CN12E-3 (LOCK) • Location of electrical component: 4-C 4. Replace FM8. 5. Replace MFPB. NOTICE • Link to the wiring diagram (N.1. bizhub C287/C227) • Link to the layout drawings for related parts by each trouble code (S.53. C3302)

Code: C3425

Description: Fusing warm-up trouble. • Detected temperature of the heating roller temperature sensor (TEMS) does not go up a given range of temperature even after a lapse of given period of time at warm up. • The temperature detected by the heating roller temperature sensor (TEMS) does not shift from the pre-standby state or the post-print color printing-enable wait state even after the lapse of a predetermined period of time after the completion of warm-up.
Causes: • Fusing unit • Heating roller temperature sensor (TEMS) • DC power supply (DCPU) • MFP board (MFPB)
Remedy: 1. Check the fusing unit for correct installation (whether it is secured in position). 2. Check the open/close operation of the right door. 3. Check the connector between the fusing unit-relay CN3-DCPU CN002 for proper connection and correct as necessary. 4. Check the connector between the fusing unit-relay CN4-MFPB CN16E for proper connection and correct as necessary. 5. Replace the fusing unit. 6. Replace MFPB. 7. Replace DCPU. NOTICE • Link to the layout drawings for related parts by each trouble code (S.54. C3425)

Code: C3722

Description: Fusing abnormally high temperature detection (Edge of the heating roller). C3722: • Detected temperature of the heating roller thermistor/1 (TH1) goes beyond a given temperature for a given period of time consecutively. • The hard protector signal remains LOW for a predetermined continuous period of time.
Causes: • Fusing unit • C3722: Heating roller thermistor/1 (TH1) • C3725: Heating roller temperature sensor (TEMS) • C3726: Heating roller thermistor/2 (TH2) • DC power supply (DCPU) • MFP board (MFPB)
Remedy: 1. Check the fusing unit for correct installation (whether it is secured in position). 2. Check the open/close operation of the right door. 3. Check the connector between the fusing unit-relay CN4-MFPB CN16E for proper connection and correct as necessary. 4. Replace the fusing unit. 5. Replace DCPU. 6. Replace MFPB. NOTICE • Link to the layout drawings for related parts by each trouble code (S.55. C3722, C3922) • Link to the layout drawings for related parts by each trouble code (S.56. C3725, C3825, C3925) • Link to the layout drawings for related parts by each trouble code (S.57. C3726, C3826, C3926)

Code: C3725

Description: Fusing abnormally high temperature detection (Main of the heating side). Detected temperature of the heating roller temperature sensor (TEMS) goes beyond a given temperature for a given period of time consecutively.
Causes: • Fusing unit • C3722: Heating roller thermistor/1 (TH1) • C3725: Heating roller temperature sensor (TEMS) • C3726: Heating roller thermistor/2 (TH2) • DC power supply (DCPU) • MFP board (MFPB)
Remedy: 1. Check the fusing unit for correct installation (whether it is secured in position). 2. Check the open/close operation of the right door. 3. Check the connector between the fusing unit-relay CN4-MFPB CN16E for proper connection and correct as necessary. 4. Replace the fusing unit. 5. Replace DCPU. 6. Replace MFPB. NOTICE • Link to the layout drawings for related parts by each trouble code (S.55. C3722, C3922) • Link to the layout drawings for related parts by each trouble code (S.56. C3725, C3825, C3925) • Link to the layout drawings for related parts by each trouble code (S.57. C3726, C3826, C3926)

Code: C3726

Description: Fusing abnormally high temperature detection (Center of the heating side). • Detected temperature of the heating roller thermistor/2 (TH2) goes beyond a given temperature for a given period of time consecutively. • The hard protector signal remains LOW for a predetermined continuous period of time.
Causes: • Fusing unit • C3722: Heating roller thermistor/1 (TH1) • C3725: Heating roller temperature sensor (TEMS) • C3726: Heating roller thermistor/2 (TH2) • DC power supply (DCPU) • MFP board (MFPB)
Remedy: 1. Check the fusing unit for correct installation (whether it is secured in position). 2. Check the open/close operation of the right door. 3. Check the connector between the fusing unit-relay CN4-MFPB CN16E for proper connection and correct as necessary. 4. Replace the fusing unit. 5. Replace DCPU. 6. Replace MFPB. NOTICE • Link to the layout drawings for related parts by each trouble code (S.55. C3722, C3922) • Link to the layout drawings for related parts by each trouble code (S.56. C3725, C3825, C3925) • Link to the layout drawings for related parts by each trouble code (S.57. C3726, C3826, C3926)
Đăng ký nhận bản tin Đăng ký nhận bản tin Đăng ký nhận bản tin Đăng ký nhận bản tin
Đăng ký nhận bản tin
Nhận ưu đãi sớm nhất khi chương trình diễn ra

Đăng ký nhận bản tin

Việc cho phép sử dụng cookie sẽ giúp cải thiện trải nghiệm của bạn trên trang web này. Chính sách cookie