Thương hiệu phân phối chính hãng
Giỏ hàng

Mã lỗi Konica-Minolta bizhub C3351 — Trang 5/18

Code: C2561, C2562, C2563, C2564

Description: • C2561: Cyan TCR sensor failure • C2562: Magenta TCR sensor failure • C2563: Yellow TCR sensor failure • C2564: Black TCR sensor failure TCR sensor automatic adjustment does not function properly, failing to adjust to an appropriate value.
Causes: • Imaging unit/Y,M,C,K • MFP board (MFPB)
Remedy: 1. Reinstall imaging unit. 2. Check the connector between imaging unit-MFPB CN19E, CN20E for proper connection and correct as necessary. 3. Replace the imaging unit. 4. Replace MFPB.

Code: C2650, C265B

Description: • C2650: Main backup media access error 1 • C265B: Main backup media access error 2. Trouble detection condition • When an error is detected at the data reading process. • The re-written data, which has been read out, checked and founded as error, is read out again and found as error. • The error was found when reading out the counter value. • The main body detects that the EEPROM is not mounted.
Causes: • MFP board (MFPB) • C2650: EEPROM/1 (EEPROM/1) • C265B: EEPROM/2 (EEPROM/2)
Remedy: 1. Make sure that EEPROM/1 and EEPROM/2 are mounted in their respective correct positions. 2. Check to see if the EEPROM is mounted in a reverse direction. 3. Check the harness from MFPB to EEPROM for proper connection and correct as necessary. 4. Replace MFPB. 5. Replace EEPROM/1 and EEPROM/2. NOTE • To replace EEPROM/2 with a new one, contact KM. 1. Replace the current EEPROM with a new one. 2. Replace the following components with new ones. When the transfer belt unit and the fusing unit have been replaced with new ones, perform [New Release] in the service mode. When the transfer roller has been replaced with a new one, perform [Counter clear]. • Imaging unit/Y,M,C,K • Transfer belt unit • Fusing unit • Transfer roller • Feed roller, separation roller (including options) • Toner filter 3. Turn ON the main power switch and check to see that warm-up is started. Make sure that malfunction codes other than C2650 or improper IU/TC placement is not detected. 4. Make the specified readjustments. 6. If the above actions do not solve the problem, contact KM.

Code: C265A

Description: Main backup media wrongly installation. The EEPROM/1 and EEPROM/2 are mounted in a reverse direction.
Causes: • EEPROM/1 (EEPROM/1) • EEPROM/2 (EEPROM/2) • MFP board (MFPB)
Remedy: 1. Check to see if the EEPROM/1 and EEPROM/2 are mounted in a reverse direction. 2. Check the type of the installed EEPROM and replace it if it is a wrong one. 3. Replace EEPROM/1 and EEPROM/2. NOTE • To replace EEPROM/2 with a new one, contact KM. 4. Replace MFPB.

Code: C2A21, C2A22, C2A23, C2A24

Description: • C2A21: Toner cartridge/C new release failure • C2A22: Toner cartridge/M new release failure • C2A23: Toner cartridge/Y new release failure • C2A24: Toner cartridge/K new release failure. Trouble detection condition The status with the new cartridge is not cleared after the new toner cartridge is set.
Causes: • Toner cartridge/Y,M,C,K • MFP board (MFPB)
Remedy: 1. Reinstall the toner cartridge 2. Clean the connection between the toner cartridge and the machine if dirty. 3. Check the connector between the toner cartridge-MFPB CN18E for proper connection and correct as necessary. 4. Replace the toner cartridge 5. Replace MFPB.

Code: C3201

Description: Fusing motor failure to turn. The motor lock signal remains HIGH for a predetermined continuous period of time while the motor is turning.
Causes: • Fusing motor (M2) • MFP board (MFPB)
Remedy: 1. Check the connector between M2-MFPB CN6E for proper connection and correct as necessary. 2. Check the loading status of the fusing unit drive, and correct the error as necessary. 3. M2 operation check • Control signal: MFPB CN6E-11 to 14 • Location of electrical component: 2-C 4. Replace M2. 5. MFPB F9E conduction check 6. Replace MFPB.

Code: C3202

Description: Fusing motor turning at abnormal timing. The motor lock signal remains LOW for a predetermined continuous period of time while the motor remains stationary.
Causes: • Fusing motor (M2) • MFP board (MFPB)
Remedy: 1. Check the connector between M2-MFPB CN6E for proper connection and correct as necessary. 2. Check the loading status of the fusing unit drive, and correct the error as necessary. 3. M2 operation check • Control signal: MFPB CN6E-11 to 14 • Location of electrical component: 2-C 4. Replace M2. 5. MFPB F9E conduction check 6. Replace MFPB.

Code: C3302

Description: Paper cooling fan motor malfunction. The fan lock signal remains HIGH for a predetermined continuous period of time while the fan is turning.
Causes: • Paper cooling fan motor (FM4) • MFP board (MFPB)
Remedy: 1. Check the connector between FM4-relay CN82-MFPB CN9E for proper connection and correct as necessary. 2. Check the fan for possible overload and correct as necessary. 3. FM4 operation check • Control signal: MFPB CN9E-6 (LOCK) • Location of electrical component: 3-C 4. Replace FM4. (bizhub C3851/C3351 / bizhub C3851FS) 5. MFPB F2E conduction check 6. Replace MFPB.

Code: C3421

Description: Fusing temperature increase malfunction (TEM1: center) • Detected temperature of the fusing temperature sensor/1 (TEM1: center and edge) does not go up a given range of temperature even after a lapse of given period of time at warm up. • The warm-up is not completed even after the set period of time has elapsed after the warm-up is started.
Causes: • Fusing unit • C3421: Fusing temperature sensor/1 (TEM1: center) • C3426: Fusing temperature sensor/1 (TEM1: edge) • DC power supply (DCPS) • MFP board (MFPB)
Remedy: 1. Check the fusing unit for correct installation (whether it is secured in position). 2. Check the open/close operation of the right door. 3. Check the fusing unit-MFPB CN13E, DCPS CN2 for proper connection and correct as necessary. 4. Replace the fusing unit. 5. Replace MFPB. 6. DCPS F102 conduction check 7. Replace DCPS.
Đăng ký nhận bản tin Đăng ký nhận bản tin Đăng ký nhận bản tin Đăng ký nhận bản tin
Đăng ký nhận bản tin
Nhận ưu đãi sớm nhất khi chương trình diễn ra

Đăng ký nhận bản tin

Việc cho phép sử dụng cookie sẽ giúp cải thiện trải nghiệm của bạn trên trang web này. Chính sách cookie