Thương hiệu phân phối chính hãng
Giỏ hàng

Mã lỗi Konica-Minolta bizhub C552DS — Trang 23/28

Code: C9401

Description: Exposure turning on the lamp trouble detection
• The output from the CCD sensor is a predetermined value or less during CCD sensor gain adjustment.
Causes: Exposure unit Flat cable Inverter board (INVB) CCD board (CCDB) Scanner relay board (REYB/SCAN) MFP board (MFPB)
Remedy: 1 Check the connection between the lamp harness and the inverter board, and correct if necessary. - - 2 Check the connection between REYB/ SCAN and the inverter board, and correct if necessary. - - 3 Check the connection between REYB/ SCAN and MFPB, and correct if necessary. - - 4 Check that the connection between CCDB and MFPB, and correct if necessary. - - 5 Change INVB - - 6 Change exposure unit - - 7 Change CCDB - - 8 Change REYB/SCAN - - 9 Change MFPB

Code: C9402

Description: Exposure turning on the lamp abnormally detection
• The average output value of the CCD sensor with the scanner at its standby position is a predetermined value or more at the end of a scan job.
Causes: Exposure unit Flat cable Inverter board (INVB) CCD board (CCDB) Scanner relay board (REYB/SCAN) MFP board (MFPB)
Remedy: 1 Check the connection between the lamp harness and the inverter board, and correct if necessary. - - 2 Check the connection between REYB/ SCAN and the inverter board, and correct if necessary. - - 3 Check the connection between REYB/ SCAN and MFPB, and correct if necessary. - - 4 Check that the connection between CCDB and MFPB, and correct if necessary. - - 5 Change INVB - - 6 Change exposure unit - - 7 Change CCDB - - 8 Change REYB/SCAN - - 9 Change MFPB

Code: C9403

Description: CIS exposure turning on the lamp trouble detection
• At the CIS gain adjustment, the machine detected that the output of the CIS exposure lamp is lower than the specified value.
Causes: CIS module (CIS) CIS inverter board (CINVB) CIS power supply (CISPU) DS image processing board (DSIPB) MFP board (MFPB)
Remedy: 1 Correct the harness connection between CIS and DSIPB if faulty. - - 2 Correct the harness connection between CIS and CINVB if faulty. - - 3 Correct the harness connection between CIS and CISPU if faulty. - - 4 Change CINVB - - 5 Change CIS - - 6 Change CISPU - - 7 Change DSIPB - - 8 Change MFPB

Code: C9404

Description: CIS exposure turning on the lamp abnormally detection
• After a scan job is completed, the machine detected that the average output of the CIS exposure lamp is greater than the specified value.
Causes: CIS module (CIS) CIS inverter board (CINVB) CIS power supply (CISPU) DS image processing board (DSIPB) MFP board (MFPB)
Remedy: 1 Correct the harness connection between CIS and DSIPB if faulty. - - 2 Correct the harness connection between CIS and CINVB if faulty. - - 3 Correct the harness connection between CIS and CISPU if faulty. - - 4 Change CINVB - - 5 Change CIS - - 6 Change CISPU - - 7 Change DSIPB - - 8 Change MFPB

Code: CA051

Description: Standard controller configuration failure
• The controller of the printer control board (PRCB) is faulty.
Causes: MFP board (MFPB)
Remedy: 1 Check to see if the following setting has been correctly made: [Service Mode] - [System 2] - [Image Controller Setting]. If changing the setting, turn OFF the main power switch and turn it ON again after 10 seconds or more. . . 2 Check the connectors of the MFP board (MFPB) for proper connection and correct as necessary. . . 3 Change MFPB

Code: CA052

Description: Controller hardware error
• A controller hardware error is detected in the network I/F.
Causes: MFP board (MFPB)
Remedy: 1 Check to see if the following setting has been correctly made: [Service Mode] - [System 2] - [Image Controller Setting]. If changing the setting, turn OFF the main power switch and turn it ON again after 10 seconds or more. . . 2 Check the connectors of the MFP board (MFPB) for proper connection and correct as necessary. . . 3 Change MFPB

Code: CA053

Description: Controller start failure
• A controller start failure is detected in the controller interface.
Causes: MFP board (MFPB)
Remedy: 1 Check to see if the following setting has been correctly made: [Service Mode] - [System 2] - [Image Controller Setting]. If changing the setting, turn OFF the main power switch and turn it ON again after 10 seconds or more. . . 2 Check the connectors of the MFP board (MFPB) for proper connection and correct as necessary. . . 3 Change MFPB

Code: CB001...CB119

Description: FAX Board Error
Causes:
Remedy:
Đăng ký nhận bản tin Đăng ký nhận bản tin Đăng ký nhận bản tin Đăng ký nhận bản tin
Đăng ký nhận bản tin
Nhận ưu đãi sớm nhất khi chương trình diễn ra

Đăng ký nhận bản tin

Việc cho phép sử dụng cookie sẽ giúp cải thiện trải nghiệm của bạn trên trang web này. Chính sách cookie