Description: CC159: ROM contents error upon startup (DSC1) CC15A: ROM contents error upon startup (DSC2)
Causes: DSC board (SC-507)
Remedy: 1 Check the DSC board connector for proper connection and correct as necessary. - - 2 Disconnect and then connect the power cord. Turn OFF the main power switch, wait for 10 sec. or more, and turn ON the main power switch. - - 3 Rewrite the firmware. - - 4 Change DSC board
Remedy: 1 Disconnect and then connect the power cord. Turn OFF the main power switch, wait for 10 sec. or more, and turn ON the main power switch. - - 2 Rewrite the firmware. - - 3 Change SDDB
Causes: Service EEPROM board (SV ERB) Printer control board (PRCB)
Remedy: 1 Rewrite the firmware. - - 2 Change PRCB 1. Turn OFF the main power switch and replace the current PRCB with a new one. (When using a PRCB of another machine in service, be sure to use a PRCB installed in the same model.) 2. Update the PRCB firmware. 3. After completing the firmware update, turn OFF and ON the main power switch and check to see that warm-up is started. 4. When the trouble cannot be solved, reinstall the removed PRCB to the original board. NOTE • When taking the above steps, check whether PRCB is defective or not without replacing the SV ERB. - - 3 Change SV ERB 1. Replace the current SV ERB with a new one. 2. Turn ON the main power switch and check to see that warm-up is started. (One minute is spent to prepare the new SV ERB for use. During the period, the control panel backlight stays off.) 3. Make the specified readjustments. - - 4 If the above actions do not solve the problem, contact KMBT.
Causes: Printer control board (PRCB) MFP board (MFPB)
Remedy: 1 Check the ROM version. - - 2 Rewrite the firmware. - - 3 Replace the corresponding board. - - 4 When not reviving even if the above-mentioned procedure is done, contact the responsible people of KMBT.
Remedy: 1 Disconnect and then connect the power cord. Turn OFF the main power switch, wait for 10 sec. or more, and turn ON the main power switch. - - 2 Rewrite the firmware. - - 3 Change DFCB
Remedy: 1 If the malfunction code gC-C172h has occurred, access [Service Mode] - [System 2] - [Image Controller Setting] and check to see if gController 2,h gController 3,h or gOthersh is set for [Image Controller Setting]. If any of these is set, according to the kind of controller, select gController 0h or gController 1.h . . 2 Change MFPB. . . 3 When not reviving even if the above-mentioned procedure is done, contact the responsible people of KMBT.
Remedy: 1 Check the hard disk connector for proper connection and correct as necessary. - - 2 Format hard disk. - - 3 Change hard disk - - 4 Change MFPB.
Remedy: 1 Turn OFF the main power switch, wait for 10 sec. or more, and turn ON the main power switch. - - 2 Reinstall the loadable device driver. - - 3 Rewrite the firmware. - - 4 Change MFPB.
Nhận ưu đãi sớm nhất khi chương trình diễn ra
Đăng ký nhận bản tin
Việc cho phép sử dụng cookie sẽ giúp cải thiện trải nghiệm của bạn trên trang web này.
Chính sách cookie
Những cookie này là cần thiết để trang web hoạt động đúng cách.
Những cookie này giúp chúng tôi hiểu cách khách truy cập tương tác với trang web.
Những cookie này được sử dụng để cung cấp quảng cáo cá nhân hóa.