Thương hiệu phân phối chính hãng
Giỏ hàng

Mã lỗi Konica-Minolta bizhub Pro 1050 — Trang 6/42

Code: SC23-10

Description: It is checked that the drum motor (M2) does not start. The drum READY2 signal (READY signal) is not detected within a specified period of time after the M2 turns ON.
Causes: Drum motor (M2) Printer control board (PRCB)
Remedy: The main body stops immediately to turn OFF the RL1 (main).

Code: SC23-11

Description: The blowout of a fuse for the intermediate hopper motor (M11) in the printer control board (PRCB) is checked. An error detection signal (blowout of a fuse) is detected when the M11 turns ON.
Causes: Intermediate hopper motor (M11) Printer control board (PRCB)
Remedy: The main body stops immediately to turn OFF the RL1 (main).

Code: SC23-12

Description: The blowout of a fuse for the air separation motor (M10) in the printer control board (PRCB) is checked. An error detection signal (blowout of a fuse) is detected when the M10 turns ON.
Causes: Air separation motor (M10) Printer control board (PRCB)
Remedy: The main body stops immediately to turn OFF the RL1 (main).

Code: SC23-13

Description: Air separation motor (M10) rotation abnormality. Since an error is detected when the M10 turn ON, turn it OFF. An error is still detected when turn it ON again.
Causes: Air separation motor (M10) Air motor encoder sensor (PS30) Resetting of the intermediate toner hopper section
Remedy: The main body stops immediately to turn OFF the RL1 (main).

Code: SC23-14

Description: The toner conveyance abnormality is detected. When toner is supplied for 8 minutes and the toner remaining sensor /1 (PS31) does not turn ON, it is found that the toner remaining sensor /3 (PS33) of the large capacity hopper turns ON for the last 15 seconds in succession.
Causes: Toner pump motor (M28) Air pump motor (M29) Toner remaining sensor /1 (PS31) Toner remaining sensor /3 (PS33) Note: • When the code SC23- 14 occurs, be sure to repair defective parts before setting the software DIPSW3-1 to 0. Setting the DIPSW3-1 to 0 without repairing defective parts may cause toner to overflow inside and outside of the machine.
Remedy: The main body stops immediately to turn OFF the RL1 (main).

Code: SC23-15

Description: Toner remaining detection sensor / 3 (PS33) abnormality. When the toner remaining sensor /1 (PS31) does not turn ON even if toner is supplied for 8 minutes, it is found that the toner remaining sensor /2 (PS32) of the large capacity hopper turns ON for the last 15 seconds in succession, and the toner remaining sensor /3 (PS33) turns OFF.
Causes: Toner remaining sensor /2 (PS32) Toner remaining sensor /3 (PS33)
Remedy: The main body stops immediately to turn OFF the RL1 (main).

Code: SC23-17

Description: Leakage at the mixing section is detected. When the toner pump motor (M28) is operating, the toner remaining sensor /4 (PS34) detects the toner being provided in succession for 20 seconds.
Causes: Toner pump motor (M28) Air pump motor (M29) Toner remaining sensor /4 (PS34) Note: • When the code SC23- 17 occurs, be sure to repair defective parts before setting the software DIPSW3-1 to 0. Setting the DIPSW3-1 to 0 without repairing defective parts may cause toner to overflow inside and outside of the machine.
Remedy: The main body stops immediately to turn OFF the RL1 (main).

Code: SC23-20

Description: Toner pump motor (M28) abnormality. The rotation of the toner pump motor (M28) and the 24 V power source are checked. While the M28 is rotating, an error detection signal (abnormal rotation) is detected for more than 1 second. At this time, an error detection signal (24V cut off) is detected.
Causes: DC power supply /2 (DCPS/ 2) Toner pump motor (M28)
Remedy: The main body stops immediately to turn OFF the RL1 (main).
Đăng ký nhận bản tin Đăng ký nhận bản tin Đăng ký nhận bản tin Đăng ký nhận bản tin
Đăng ký nhận bản tin
Nhận ưu đãi sớm nhất khi chương trình diễn ra

Đăng ký nhận bản tin

Việc cho phép sử dụng cookie sẽ giúp cải thiện trải nghiệm của bạn trên trang web này. Chính sách cookie