Thương hiệu phân phối chính hãng
Giỏ hàng

Mã lỗi Konica-Minolta bizhub Pro 1050e — Trang 5/42

Code: SC23-02

Description: The speed error signal of the developing motor (M3) is checked. Since an error detection signal is detected a second after the M3 turns ON, turn OFF the M3 for 0.5 seconds. Then, an error detection signal is detected again a second after it is turned ON again.
Causes: Developing motor (M3) Printer control board (PRCB)
Remedy: The main body stops immediately to turn OFF the RL1 (main).

Code: SC23-03

Description: The locking of the blade motor is detected. The error detection signal (over current) of the M22 is detected.
Causes: Blade motor (M22) Blade sensor /1 (PS24), /2 (PS25)
Remedy: The main body stops immediately to turn OFF the RL1 (main).

Code: SC23-04

Description: It is checked that the movement of the blade motor (M22) is not completed, and the 24V power source is also checked. The drum READY1 signal (READY condition) cannot be detected within a specified period of time after the drum motor (M2) turns ON. Or, the drum READY1 signal (READY release condition) cannot be detected within a specified period of time after the M2 turns OFF. At this time, an error detection signal (24V cut out) is detected.
Causes: DC power supply /2 (DCPS/ 2)
Remedy: The main body stops immediately to turn OFF the RL1 (main).

Code: SC23-05

Description: The blowout of a fuse for the blade motor (M22) in the printer control board (PRCB) is checked. The drum READY1 signal (READY condition) cannot be detected within a specified period of time after the drum motor (M2) turns ON. Or, the drum READY1 signal (READY release condition) cannot be detected within a specified period of time after the M2 turns OFF. At this time, the error detection signal (blowout of a fuse) of the blade motor (M22) is detected.
Causes: Blade motor (M22) Printer control board (PRCB)
Remedy: The main body stops immediately to turn OFF the RL1 (main).

Code: SC23-06

Description: It is checked that the movement of the blade motor (M22) is not completed. The drum READY1 signal (READY condition) cannot be detected within a specified period of time after the drum motor (M2) turns ON. Or, the drum READY1 signal (READY release condition) cannot be detected within a specified period of time after the M2 turns OFF. At this time, an error detection signal is not detected.
Causes: Blade motor (M22) Printer control board (PRCB)
Remedy: The main body stops immediately to turn OFF the RL1 (main).

Code: SC23-07

Description: It is checked that the movement of the blade motor (M22) is not completed, and 24V power source is also checked. The blade READY signal (READY condition) cannot be detected within a specified period of time after the blade replacement signal turns ON. Or, the blade READY signal (READY release condition) cannot be detected within a specified period of time after the blade replacement signal turns OFF. At this time, an error detection signal (24V cut off) is detected.
Causes: DC power supply /2 (DCPS/ 2)
Remedy: The main body stops immediately to turn OFF the RL1 (main).

Code: SC23-08

Description: The blowout of a fuse for the blade motor (M22) in the printer control board (PRCB) is checked. The blade READY signal (READY condition) cannot be detected within a specified period of time after the blade replacement signal turns ON. Or, the blade READY signal (READY release condition) cannot be detected within a specified period of time after the blade replacement signal turns OFF. At this time, an error detection signal (blowout of a fuse) of the blade motor (M22) is detected.
Causes: Blade motor (M22) Printer control board (PRCB)
Remedy: The main body stops immediately to turn OFF the RL1 (main).

Code: SC23-09

Description: It is checked that the movement of the blade motor (M22) is not completed. The blade READY signal (READY condition) cannot be detected within a specified period of time after the blade replacement signal turns ON. Or, the blade READY signal (READY release condition) cannot be detected within a specified period of time after the blade replacement signal turns OFF. At this time, an error detection signal is not detected.
Causes: Blade motor (M22) Printer control board (PRCB)
Remedy: The main body stops immediately to turn OFF the RL1 (main).
Đăng ký nhận bản tin Đăng ký nhận bản tin Đăng ký nhận bản tin Đăng ký nhận bản tin
Đăng ký nhận bản tin
Nhận ưu đãi sớm nhất khi chương trình diễn ra

Đăng ký nhận bản tin

Việc cho phép sử dụng cookie sẽ giúp cải thiện trải nghiệm của bạn trên trang web này. Chính sách cookie