Thương hiệu phân phối chính hãng
Giỏ hàng

Mã lỗi Konica-Minolta bizhub Pro 1051 — Trang 9/91

Code: C-0250

Description: PI-PFU (PF-703) upper tray up abnormality. When the upper limit sensor /1 (PS5) is OFF, PS5 does not turn ON within 20seconds after the paper lift motor /1 (M7) turns ON for lifting operation. Or, the paper suction sensor /Fr1 and /Rr1 (PS25 and PS26) turn ON before PS5 turns ON while in tray lifting.
Causes: Upper limit sensor /1 (PS2: PF-702) Upper limit sensor /1 (PS5: PF-703) Paper lift motor /1 (M42: PF-702) Paper lift motor /1 (M7: PF-703) PF drive board (PFUDB: PF-702/703)
Remedy: 1 Check the paper loaded condition and the rear end restriction plate misaligned of the upper tray, and repair it if any abnormality. - 2 Check the connector connection and the wiring between PFUDB and motor/sensor, and repair it if any abnormality. - 3 Check the I/O drive of the motor and the coupling of the gear, and repair/replace it if any abnormality. PF-702: 5-C PF-703: 6-F 4 Check I/O and the operation of the sensor, and repair it if any abnormality. PF-702: 3-C PF-703: 3-F 5 Replace PS2: PF-702 or PS5: PF-703. - 6 Replace M42: PF -702 or M7: PF-703. - 7 Replace PFUDB.

Code: C-0251

Description: The locking of the upper tray paper lift motor /1 (M7) is detected. When M7 is ON, an error detection signal of the M7 is detected.
Causes: Paper lift motor /1 (M42: PF-702) Paper lift motor /1 (M7: PF-703) PF drive board (PFUDB: PF-702/703)
Remedy: 1 Check the connector connection and the wiring between PFUDB and the motor, and repair it if any abnormality. - 2 Check the I/O drive of the motor and the coupling of the gear, and repair/replace it if any abnormality. PF-702: 5-C PF-703: 6-F 3 Replace M42: PF -702 or M7: PF-703. - 4 Replace PFUDB.

Code: C-0252

Description: PI-PFU (PF-703) middle tray up abnormality. When the upper limit sensor /2 (PS9) is OFF, PS9 does not turn ON within 20seconds after the paper lift motor /2 (M8) turns ON for lifting operation. Or, the paper suction sensor /Fr2 and /Rr2 (PS27 and PS28) turn ON before PS9 turns ON while in tray lifting.
Causes: Upper limit sensor /2 (PS6: PF-702) Upper limit sensor /2 (PS9: PF-703) Paper lift motor /2 (M43: PF-702) Paper lift motor /2 (M8: PF-703) PF drive board (PFUDB: PF-702/703)
Remedy: 1 Check the paper loaded condition and the rear end restriction plate misaligned of the middle tray, and repair it if any abnormality. - 2 Check the connector connection and the wiring between PFUDB and motor/sensor, and repair it if any abnormality. - 3 Check the I/O drive of the motor and the coupling of the gear, and repair/replace it if any abnormality. PF-702: 7-C PF-703: 12-F 4 Check I/O and the operation of the sensor, and repair it if any abnormality. PF-702: 5-C PF-703: 9-F 5 Replace PS6: PF-702 or PS9: PF-703. - 6 Replace M43: PF -702 or M8: PF-703. - 7 Replace PFUDB.

Code: C-0253

Description: The locking of the middle tray paper lift motor /2 (M8) is detected. When M8 is ON, an error detection signal of the M8 is detected.
Causes: Paper lift motor /2 (M43: PF-702) Paper lift motor /2 (M8: PF-703) PF drive board (PFUDB: PF-702/703)
Remedy: 1 Check the connector connection and the wiring between PFUDB and the motor, and repair it if any abnormality. - 2 Check the I/O drive of the motor and the coupling of the gear, and repair/replace it if any abnormality. PF-702: 7-C PF-703: 12-F 3 Replace M43: PF -702 or M8: PF-703. - 4 Replace PFUDB.

Code: C-0254

Description: PI-PFU (PF-703) lower tray up abnormality. When the upper limit sensor /3 (PS13) is OFF, PS13 does not turn ON within 20seconds after the paper lift motor /3 (M9) turns ON for lifting operation. Or, the paper suction sensor /Fr3 and /Rr3 (PS29 and PS30) turn ON before PS13 turns ON while in tray lifting.
Causes: Upper limit sensor /3 (PS10: PF-702) Upper limit sensor /3 (PS13: PF-703) Paper lift motor /3 (M44: PF-702) Paper lift motor /3 (M9: PF-703) PF drive board (PFUDB: PF-702/703)
Remedy: 1 Check the paper loaded condition and the rear end restriction plate misaligned of the lower tray, and repair it if any abnormality. - 2 Check the connector connection and the wiring between PFUDB and motor/sensor, and repair it if any abnormality. - 3 Check the I/O drive of the motor and the coupling of the gear, and repair/replace it if any abnormality. PF-702: 9-C PF-703: 19-F 4 Check I/O and the operation of the sensor, and repair it if any abnormality. PF-702: 7-C PF-703: 16-F 5 Replace PS10: PF-702 or PS13: PF-703. - 6 Replace M44: PF-702 or M9: PF703. - 7 Replace PFUDB.

Code: C-0255

Description: The locking of the lower tray paper lift motor /3 (M9) is detected. When M9 is ON, an error detection signal of the M9 is detected.
Causes: Paper lift motor /3 (M44: PF-702) Paper lift motor /3 (M9: PF-703) PF drive board (PFUDB: PF-702/703)
Remedy: 1 Check the connector connection and the wiring between PFUDB and the motor, and repair it if any abnormality. - 2 Check the I/O drive of the motor and the coupling of the gear, and repair/replace it if any abnormality. PF-702: 9-C PF-703: 19-F 3 Replace M44: PF -702 or M9: PF-703. - 4 Replace PFUDB.

Code: C-0261

Description: 1st tandem PF-703 shutter motor /1 (M10) operation time abnormality 1. The M10EM error detection signal is detected twice in succession within a specified period of time after M10 was turned ON. At this time, an error detection signal (blowout of fan ICP) is not detected.
Causes: Shutter motor /1 (M10: PF-703) PF drive board (PFUDB: PF-703)
Remedy: 1 Check the connector connection and the wiring between PFUDB and the motor, and repair it if any abnormality. - 2 Check the I/O drive of the motor and the coupling of the gear, and repair/replace it if any abnormality. PF-703: 15-L 3 Replace M10. - 4 Replace PFUDB.

Code: C-0262

Description: 1st tandem PF-703 shutter motor /1 (M10) operation time abnormality 2. The M10EM error detection signal is detected twice in succession within a specified period of time after M10 was turned ON. At this time, an error detection signal (blowout of ICP) is detected.
Causes: Shutter motor /1 (M10: PF-703) PF drive board (PFUDB: PF-703)
Remedy: 1 Check the connector connection and the wiring between PFUDB and the motor, and repair it if any abnormality. - 2 Check the I/O drive of the motor and the coupling of the gear, and repair/replace it if any abnormality. PF-703: 15-L 3 Replace M10 and PFUDB at a time.
Đăng ký nhận bản tin Đăng ký nhận bản tin Đăng ký nhận bản tin Đăng ký nhận bản tin
Đăng ký nhận bản tin
Nhận ưu đãi sớm nhất khi chương trình diễn ra

Đăng ký nhận bản tin

Việc cho phép sử dụng cookie sẽ giúp cải thiện trải nghiệm của bạn trên trang web này. Chính sách cookie