Code :

Code: C-0204
Description: The locking of the tray lift-up motor /1 (M25) is detected. An error detection signal of M25 is detected while M25 is ON.
Causes: Tray lift-up motor /1 (M25) Printer control board (PRCB)
Remedy: 1 Check the connector connection and the wiring between PRCB and the motor, and repair it if any abnormality. - 2 Check the I/O drive of the motor and the coupling of the gear, and repair/replace it if any abnormality. 5-F 3 Replace M25. - 4 Replace PRCB.

Code: C-0205
Description: Tray /2 up abnormality 1. When the upper limit sensor /2 (PS10) is OFF, PS10 does not turn ON within 20seconds after the tray lift-up motor /2 (M34) turns ON for lifting operation. At this time, an error detection signal (24V cut off) is detected.
Causes: Upper limit sensor /2 (PS10) Tray lift-up motor /2 (M34) Printer control board (PRCB) DC power supply /2 (DCPS /2)
Remedy: 1 Check the paper loaded condition and the rear end restriction plate condition of the tray 2, and repair it if any abnormality. - 2 Check the connector connection and the wiring between PRCB and motor/sensor, and repair it if any abnormality. - 3 Check the I/O drive of the motor and the coupling of the gear, and repair/replace it if any abnormality. 8-F 4 Check I/O and the operation of the sensor, and repair/replace it if any abnormality. 6-G 5 Replace PS10. - 6 Replace M34. - 7 Replace PRCB. - 8 Replace DCPS /2.

Code: C-0207
Description: Tray /2 up abnormality 2. When the upper limit sensor /2 (PS10) is OFF, PS10 does not turn ON within 20seconds after the tray lift-up motor /2 (M34) turns ON for lifting operation. At this time, an error detection signal is not detected.
Causes: Upper limit sensor /2 (PS10) Tray lift-up motor /2 (M34) Printer control board (PRCB) DC power supply /2 (DCPS /2)
Remedy: 1 Check the paper loaded condition and the rear end restriction plate condition of the tray 2, and repair it if any abnormality. - 2 Check the connector connection and the wiring between PRCB and motor/sensor, and repair it if any abnormality. - 3 Check the I/O drive of the motor and the coupling of the gear, and repair/replace it if any abnormality. 8-F 4 Check I/O and the operation of the sensor, and repair/replace it if any abnormality. 6-G 5 Replace PS10. - 6 Replace M34. - 7 Replace PRCB. - 8 Replace DCPS /2.

Code: C-0208
Description: The locking of the tray lift-up motor /2 (M34) is detected. When M34 is ON, an error detection signal of the M34 is detected.
Causes: Tray lift-up motor /2 (M34) Printer control board (PRCB)
Remedy: 1 Check the connector connection and the wiring between PRCB and the motor, and repair it if any abnormality. - 2 Check the I/O drive of the motor and the coupling of the gear, and repair/replace it if any abnormality. 8-F 3 Replace M34. - 4 Replace PRCB.

Code: C-0222
Description: 1st tandem PF-702/703 upper tray up abnormality. PF-702: When the upper limit sensor /1 (PS2) is OFF, PS2 does not turn ON within 20seconds after the paper lift motor /1 (M42) turns ON for lifting operation. PF-703: When the upper limit sensor /1 (PS5) is OFF, PS5 does not turn ON within 20seconds after the paper lift motor /1 (M7) turns ON for lifting operation. Or, the paper suction sensor /Fr1 and /Rr1 (PS25 and PS26) turn ON before PS5 turns ON while in tray lifting.
Causes: Upper limit sensor /1 (PS2: PF-702) Upper limit sensor /1 (PS5: PF-703) Paper lift motor /1 (M42: PF-702) Paper lift motor /1 (M7: PF-703) PF drive board (PFUDB: PF-702/703)
Remedy: 1 Check the paper loaded condition and the rear end restriction plate misaligned of the upper tray, and repair it if any abnormality. - 2 Check the connector connection and the wiring between PFUDB and motor/sensor, and repair it if any abnormality. - 3 Check the I/O drive of the motor and the coupling of the gear, and repair/replace it if any abnormality. PF-702: 5-C PF-703: 6-F 4 Check I/O and the operation of the sensor, and repair it if any abnormality. PF-702: 3-C PF-703: 3-F 5 Replace PS2: PF-702 or PS5: PF-703. - 6 Replace M42: PF -702 or M7: PF-703. - 7 Replace PFUDB.

Code: C-0223
Description: The locking of the paper lift motor /1 of the 1st tandem PF-702/703 upper tray (M42: PF-702, M7: PF-703) is detected. When M42 and M7 are ON, error detection signals of the M42 and M7 are detected.
Causes: Paper lift motor /1 (M42: PF-702) Paper lift motor /1 (M7: PF-703) PF drive board (PFUDB: PF-702/703)
Remedy: 1 Check the connector connection and the wiring between PFUDB and the motor, and repair it if any abnormality. - 2 Check the I/O drive of the motor and the coupling of the gear, and repair/replace it if any abnormality. PF-702: 5-C PF-703: 6-F 3 Replace M42: PF -702 or M7: PF-703. - 4 Replace PFUDB.

Code: C-0226
Description: 1st tandem PF-702/703 middle tray up abnormality. PF-702: When the upper limit sensor /2 (PS6) is OFF, PS6 does not turn ON within 20seconds after the paper lift motor /2 (M43) turns ON for lifting operation. PF-703: When the upper limit sensor /2 (PS9) is OFF, PS9 does not turn ON within 20seconds after the paper lift motor /2 (M8) turns ON for lifting operation. Or, the paper suction sensor /Fr2 and /Rr2 (PS27 and PS28) turn ON before PS9 turns ON while in tray lifting.
Causes: Upper limit sensor /2 (PS6: PF-702) Upper limit sensor /2 (PS9: PF-703) Paper lift motor /2 (M43: PF-702) Paper lift motor /2 (M8: PF-703) PF drive board (PFUDB: PF-702/703)
Remedy: 1 Check the paper loaded condition and the rear end restriction plate misaligned of the middle tray, and repair it if any abnormality. - 2 Check the connector connection and the wiring between PFUDB and motor/sensor, and repair it if any abnormality. - 3 Check the I/O drive of the motor and the coupling of the gear, and repair/replace it if any abnormality. PF-702: 7-C PF-703: 12-F 4 Check I/O and the operation of the sensor, and repair it if any abnormality. PF-702: 5-C PF-703: 9-F 5 Replace PS6: PF-702 or PS9: PF-703. - 6 Replace M43: PF -702 or M8: PF-703. - 7 Replace PFUDB.

Code: C-0227
Description: The locking of the paper lift motor /2 of the 1st tandem PF-702/703 middle tray (M43: PF-702, M8: PF-703) is detected. When M43 and M8 are ON, error detection signals of the M43 and M8 are detected.
Causes: Paper lift motor /2 (M43: PF-702) Paper lift motor /2 (M8: PF-703) PF drive board (PFUDB: PF-702/703)
Remedy: 1 Check the connector connection and the wiring between PFUDB and the motor, and repair it if any abnormality. - 2 Check the I/O drive of the motor and the coupling of the gear, and repair/replace it if any abnormality. PF-702: 7-C PF-703: 12-F 3 Replace M43: PF -702 or M8: PF-703. - 4 Replace PFUDB.