Description: Abnormally low fusing temperature
• The fusing temperature remains 105 °C or less for a continuous 0.1-sec. period or more during the standby state or printing. • The fusing temperature remains a level lower than the following temperature for a continuous 2-min. period or more during the low-temperature standby state. 35-cpm copier: 105 °C 25-cpm copier: 80 °C 20-cpm copier (U.S.A. and Canada only): 80 °C
Remedy: 1 Fusing Roller Heater Lamp turns ON when the Side Cover is opened and closed. NO Check step 3 and onward. 2 The resistance of Fusing Roller Thermistor (across CN25-2 and 3 on the Fusing Unit end) is infinity. YES Change Fusing Roller Thermistor. NO Change Master Board. 3 There is continuity across CN3-1 and 2 on the Fusing Unit end. YES Check step 7. 4 Fusing Roller Heater Lamp is conducting. NO Change Fusing Roller Heater Lamp. 5 Fusing Roller Thermostat is conducting. NO Change Fusing Roller Thermostat. 6 Fusing Roller Heater Lamp Fuse is conducting. NO Change Fusing Roller Heater Lamp Fuse. 7 There is continuity across 1A and 1B, and across 2A and 2B, when Side Cover Interlock Switch 2 is actuated. YES Change Power Supply Unit. Change Master Board. NO Change Side Cover Interlock Switch 2.
Description: Abnormally high fusing temperature
The fusing temperature remains 230 °C or more for a continuous 0.1-sec. period or more.
Remedy: 1 Fusing Roller Thermistor is dirty. YES Clean. 2 The circuit across CN25-2 and -3 on the Fusing Unit end is shorted. YES Change Fusing Roller Thermistor. NO Change Master Board.
Description: Faulty Scanner Home Position Sensor 1
<The Power Switch is turned ON, Original Cover lowered, or Start key pressed when the Scanner is at its home position> • The Scanner Home Position Sensor 1 is not unblocked (H) even when the Scanner moves 10 mm to the left. • The Scanner Home Position Sensor 1 is not blocked (L) even when the Scanner moves 4 mm to the right after the Scanner Home Position Sensor 1 has been unblocked (H). <The Power Switch is turned ON, Original Cover lowered, or Start key pressed when the Scanner is at any position other than home> • The Scanner Home Position Sensor 1 is not blocked (L) even when the Scanner moves 469.5 mm to the right.
Remedy: 1 Scanner Motor operation check: Select functions in the following order: Tech. Rep. Mode - Movement Check - Scanner; set +1000 in Relative Position?h and touch Set?h; the Scanner moves at this time. YES Check step 3 and onward. 2 The Scanner can be moved manually. YES Change Scanner Motor. Change BCR Board. Change MFB2 Board. Change Master Board. NO Correct drive coupling. 3 C0651 is displayed. YES Check step 7 and onward. 4 Scanner Home Position Sensor 1 operation check through I/O check YES Check to see if Scanner Home Position Sensor 1 is blocked as the Scanner is moved. If it is checked okay, change Master Board. 5 Scanner Home Position Sensor 1 operation check: the voltage across CN11BCR-1 on BCR Board and GND is DC0 V when the sensor is blocked and DC5 V when the sensor is unblocked. NO Change Scanner Home Position Sensor 1. 6 Scanner Home Position Sensor 1 operation check: the voltage across CN1BCR-26 on BCR Board and GND is DC0 V when the sensor is blocked and DC5 V when the sensor is unblocked. YES Change BCR Board. NO Change MFB2 Board. Change Master Board. 7 Scanner Home Position Sensor 2 operation check through I/O check YES Check to see if Scanner Home Position Sensor 2 is blocked as the Scanner is moved. If it is checked okay, change Master Board. 8 Scanner Home Position Sensor 2 operation check: the voltage across CN12BCR-1 on BCR Board and GND is DC0 V when the sensor is blocked and DC5 V when the sensor is unblocked. NO Change Scanner Home Position Sensor 2. 9 Scanner Home Position Sensor 2 operation check: the voltage across CN1BCR-27 on BCR Board and GND is DC0 V when the sensor is blocked and DC5 V when the sensor is unblocked. YES Change BCR Board. NO Change MFB2 Board. Change Master Board.
Description: Faulty Scanner Home Position Sensor 2
When the Start key is pressed with a document loaded in the Document Feed Tray of the ADF, Scanner Home Position Sensor 2 is not blocked (L) even when the Scanner moves 463 mm to the left after the sensor has been unblocked (H).
Remedy: 1 Scanner Motor operation check: Select functions in the following order: Tech. Rep. Mode - Movement Check - Scanner; set +1000 in Relative Position?h and touch Set?h; the Scanner moves at this time. YES Check step 3 and onward. 2 The Scanner can be moved manually. YES Change Scanner Motor. Change BCR Board. Change MFB2 Board. Change Master Board. NO Correct drive coupling. 3 C0651 is displayed. YES Check step 7 and onward. 4 Scanner Home Position Sensor 1 operation check through I/O check YES Check to see if Scanner Home Position Sensor 1 is blocked as the Scanner is moved. If it is checked okay, change Master Board. 5 Scanner Home Position Sensor 1 operation check: the voltage across CN11BCR-1 on BCR Board and GND is DC0 V when the sensor is blocked and DC5 V when the sensor is unblocked. NO Change Scanner Home Position Sensor 1. 6 Scanner Home Position Sensor 1 operation check: the voltage across CN1BCR-26 on BCR Board and GND is DC0 V when the sensor is blocked and DC5 V when the sensor is unblocked. YES Change BCR Board. NO Change MFB2 Board. Change Master Board. 7 Scanner Home Position Sensor 2 operation check through I/O check YES Check to see if Scanner Home Position Sensor 2 is blocked as the Scanner is moved. If it is checked okay, change Master Board. 8 Scanner Home Position Sensor 2 operation check: the voltage across CN12BCR-1 on BCR Board and GND is DC0 V when the sensor is blocked and DC5 V when the sensor is unblocked. NO Change Scanner Home Position Sensor 2. 9 Scanner Home Position Sensor 2 operation check: the voltage across CN1BCR-27 on BCR Board and GND is DC0 V when the sensor is blocked and DC5 V when the sensor is unblocked. YES Change BCR Board. NO Change MFB2 Board. Change Master Board.
Remedy: 1 The voltage across CN1A-15 on LCC Control Board and GND is DC24 V. YES Change LCC Lift-Up Motor. Change LCC Control Board. Change Control Board. Change Master Board. 2 Fuse is conducting. YES Change Power Supply Unit. NO Change fuse.
Remedy: 1 Lift-Up Sensor 1 operation check through I/O check YES Check step 3 and onward. 2 Lift-Up Sensor 1 operation check: the voltage across CN4A-6 on LCC Control Board and GND is DC5 V when the sensor is blocked and DC0 V when the sensor is unblocked. YES Change LCC Control Board. Change Control Board. Change Master Board. NO Check actuator. Change Lift-Up Sensor 1. 3 LCC Lift-Up Motor operation check: LCC Lift- Up Motor turns after the cassette has been slid into the copier. YES Change Master Board. 4 LCC Lift-Up Motor operation check: the voltage across CN5A-1 on LCC Control Board and GND changes from DC0 V to DC24 V while step 3 is being performed. YES Change LCC Lift-Up Motor. NO Change LCC Control Board. Change Control Board. Change Master Board.
Remedy: 1 The voltage across CN1A-15 on LCC Control Board and GND is DC24 V. YES Change LCC Transport Motor. Change LCC Control Board. Change Control Board. Change Master Board. 2 Fuse is conducting. YES Change Power Supply Unit. NO Change fuse.
Remedy: 1 Lift-Up Sensor 2 operation check through I/O check YES Check step 3 and onward. 2 Lift-Up Sensor 2 operation check: the voltage across CN4A-9 on LCC Control Board and GND is DC5 V when the sensor is blocked and DC0 V when the sensor is unblocked. YES Change LCC Control Board. Change Control Board. Change Master Board. NO Check actuator. Change Lift-Up Sensor 2. 3 LCC Lift-Up Motor operation check: LCC Lift- Up Motor turns after the cassette has been slid into the copier. YES Change Master Board. 4 LCC Lift-Up Motor operation check: the voltage across CN5A-2 on LCC Control Board and GND changes from DC0 V to DC24 V while step 3 is being performed. YES Change LCC Lift-Up Motor. NO Change LCC Control Board. Change Control Board. Change Master Board.
Nhận ưu đãi sớm nhất khi chương trình diễn ra
Đăng ký nhận bản tin
Việc cho phép sử dụng cookie sẽ giúp cải thiện trải nghiệm của bạn trên trang web này.
Chính sách cookie
Những cookie này là cần thiết để trang web hoạt động đúng cách.
Những cookie này giúp chúng tôi hiểu cách khách truy cập tương tác với trang web.
Những cookie này được sử dụng để cung cấp quảng cáo cá nhân hóa.