Description: Laser malfunction
• The SOS signal is not detected within a predetermined period of time after the output of a laser has been started. • The SOS signal is never detected in the image area
Remedy: 1 Check the cable and connector for proper connection and correct as necessary. 2 Change PH unit. 3 Change PRCB.
Description: Fuser warm-up failure
• The thermistor does not detect a predetermined temperature value even after the lapse of a predetermined period of time after the current warm-up cycle has been started and the current warm-up cycle is thus not completed.
Remedy: 1 Change fuser unit. 2 For magicolor 1600W: 2.1. Main switch is turned ON. 2.2. Open the top cover. 2.3. Press the following keys in this order. Rotate Toner key - Clear key - Clear key - Rotate Toner key. 2.4. Main switch is turned OFF/ON. For magicolor 1650EN: 2.1. Main switch is turned ON. 2. Execute [SERVICE MENU] - [FUSER UNLOCK]. 3 Change PRCB. 4 Change DCPU.
Description: Thermistor open-circuit failure
• The temperature detected by the thermistor does not reach a predetermined level even after the lapse of a given period time after the warm-up cycle has been started.
Remedy: 1 Check the fuser unit for correct installation (whether it is secured in position). 2 Check the fuser unit, DCPU, and PRCB for proper connection and correct as necessary. 3 Change fuser unit. 4 Change PRCB. 5 Change DCPU.
Description: Thermistor resistance failure
• The heater lamp remains ON for a predetermined consecutive period of time.
Remedy: 1 Change fuser unit. 2 For magicolor 1600W: 2.1. Main switch is turned ON. 2.2. Open the top cover. 2.3. Press the following keys in this order. Rotate Toner key - Clear key - Clear key - Rotate Toner key. 2.4. Main switch is turned OFF/ON. For magicolor 1650EN: 2.1. Main switch is turned ON. 2. Execute [SERVICE MENU] - [FUSER UNLOCK]. 3 Change PRCB. 4 Change DCPU.
Description: Abnormally low fuser temperature
• The temperature detected by the thermistor remains lower than a predetermined value for a predetermined period of time.
Remedy: 1 Check the fuser unit for correct installation (whether it is secured in position). 2 Check the fuser unit, DCPU, and PRCB for proper connection and correct as necessary. 3 Change fuser unit. 4 Change PRCB. 5 Change DCPU.
Description: Abnormally high fuser temperature
• The temperature detected by the thermistor is a predetermined value or higher for a predetermined period of time.
Remedy: 1 Check the fuser unit for correct installation (whether it is secured in position). 2 Check the fuser unit, DCPU, and PRCB for proper connection and correct as necessary. 3 Change fuser unit. 4 Change PRCB. 5 Change DCPU.
Description: Printer control board malfunction
• Communications with the M/C expansion IO G/A (IC on the printer control board) are not properly carried out.
Remedy: 1 Check the PRCB connector for proper connection and correct as necessary. 2 Change PRCB.
Nhận ưu đãi sớm nhất khi chương trình diễn ra
Đăng ký nhận bản tin
Việc cho phép sử dụng cookie sẽ giúp cải thiện trải nghiệm của bạn trên trang web này.
Chính sách cookie
Những cookie này là cần thiết để trang web hoạt động đúng cách.
Những cookie này giúp chúng tôi hiểu cách khách truy cập tương tác với trang web.
Những cookie này được sử dụng để cung cấp quảng cáo cá nhân hóa.