Thương hiệu phân phối chính hãng
Giỏ hàng

Mã lỗi Konica-Minolta Magicolor 2300W — Trang 2/3

Code: 16

Description: • If the transfer belt of the transport image transfer belt unit does not rotate
Remedy: 1 Replace the image transfer belt unit.

Code: 17

Description: • If the toner cartridge does not rotate
Remedy: 1 Check PC4 operation. PC4_ON 3-F. 2 Check CL1 operation. CL1_REM 2-F. 3 Check M2 operation 3-E. 4 Replace PWB-A. 5 Replace PWB-P.

Code: 18

Description: • If the unit does reach 80° C within 100 seconds from the time that warm-up begins • If the temperature of the fusing roller falls below 70° C in 10 seconds during standby • If the temperature of the fusing roller increases to 220°C in 0.1 second
Remedy: 1 Check for continuity at H1 and H2. NO Replace H1 and H2. 2-B, 2-C 2 Check for continuity at TS1. NO Replace TS1. 2-C. 3 Is the resistance at TH1 infinite? (between CN18-1 and -2 on the thermistor) YES Clean TH1 or replace the fusing unit. HEATER 2-D NO Replace PU. Replace PWB-A.1

Code: 19

Description: • If the unit does reach 80° C within 100 seconds from the time that warm-up begins • If the temperature of the fusing roller falls below 70° C in 10 seconds during standby • If the temperature of the fusing roller increases to 220°C in 0.1 second
Remedy: 1 Check for continuity at H1 and H2. NO Replace H1 and H2. 2-B, 2-C 2 Check for continuity at TS1. NO Replace TS1. 2-C. 3 Is the resistance at TH1 infinite? (between CN18-1 and -2 on the thermistor) YES Clean TH1 or replace the fusing unit. HEATER 2-D NO Replace PU. Replace PWB-A.1

Code: 1A

Description: • If the temperature of the fusing roller when the fusing unit begins warming up does not remain increased by 5°C for 1 second within the 40 to 50 seconds after the fusing roller begins warming up
Remedy: 1 Is there a short circuit at TH1? (between CN18-1 and -2 on the thermistor) YES Clean TH1. HEATER 2-D Replace the fusing unit. NO Replace PU. Replace PWB-AP.

Code: 1B

Description: • If the temperature of the fusing roller when the fusing unit begins warming up does not remain increased by 5°C for 1 second within the 40 to 50 seconds after the fusing roller begins warming up
Remedy: 1 Is there a short circuit at TH1? (between CN18-1 and -2 on the thermistor) YES Clean TH1. HEATER 2-D Replace the fusing unit. NO Replace PU. Replace PWB-AP.

Code: 21

Description: • If a overhead projector transparency is not detected
Remedy: 1 Check PC3A operation. PC3_REM 5-D. 2 Replace PWB-A. 3 Replace PWB-P.

Code: 29

Description: • If the EEPROM malfunctioned
Remedy: 1 Replace the EEPROM. 2 Replace PWB-A.
Đăng ký nhận bản tin Đăng ký nhận bản tin Đăng ký nhận bản tin Đăng ký nhận bản tin
Đăng ký nhận bản tin
Nhận ưu đãi sớm nhất khi chương trình diễn ra

Đăng ký nhận bản tin

Việc cho phép sử dụng cookie sẽ giúp cải thiện trải nghiệm của bạn trên trang web này. Chính sách cookie