Thương hiệu phân phối chính hãng
Giỏ hàng

Mã lỗi Konica-Minolta Magicolor 4750EN — Trang 2/5

Code: 0300

Display: POLYGON MOT
Description: Polygon motor malfunction
• The polygon motor does not rotate evenly even after the lapse of a given period of time after it has been started. • The motor lock signal remains HIGH for a given period of consecutive time while the polygon motor is being rotated.
Remedy: 1 Check the connector between PH unit- PRCB PJ18 for proper connection and correct as necessary. 2 Change PH unit. 3 Change PRCB.

Code: 0310

Display: LASER ERROR
Description: Laser malfunction
• The SOS signal is not detected within a given period of time after the output of the laser has been started.
Remedy: 1 Check the connector between PH unit- PRCB PJ18 for proper connection and correct as necessary. 2 Check the connector between PH unit- MFPB CN15 for proper connection and correct as necessary. 3 Change PH unit. 4 Change PRCB.

Code: 0500

Display: FUSER ERROR
Description: Heating roller warm-up failure
• The thermistor /1 does not detect the specified temperature and the warm-up cycle is not completed even after the lapse of a given period of time after the cycle has been started.
Remedy: 1 Check the fuser unit for correct installation (whether it is secured in position). 2 Check the connector between fuser unit- PRCB PJ9 for proper connection and correct as necessary. 3 Check the connector between fuser unit- DCPU CN2 for proper connection and correct as necessary. 4 Change fuser unit. 5 Change PRCB. 6 Change DCPU.

Code: 0502

Display: TERMISTOR1
Description: Thermistor open-circuit failure
• The temperature detected by the thermistor/1 does not reach a predetermined level even after the lapse of a given period time after the warm-up cycle has been started.
Remedy: 1 Check the fuser unit for correct installation (whether it is secured in position). 2 Check the connector between fuser unit- PRCB PJ9 for proper connection and correct as necessary. 3 Check the connector between fuser unit- DCPU CN2 for proper connection and correct as necessary. 4 Change fuser unit. 5 Change PRCB. 6 Change DCPU.

Code: 0503

Display: TERMISTOR2
Description: Thermistor resistance failure
• The difference between the temperature detected by thermistor/1 and that detected by thermistor/2 exceeds a predetermined value.
Remedy: 1 Check the fuser unit for correct installation (whether it is secured in position). 2 Check the connector between fuser unit- PRCB PJ9 for proper connection and correct as necessary. 3 Check the connector between fuser unit- DCPU CN2 for proper connection and correct as necessary. 4 Change fuser unit. 5 Change PRCB. 6 Change DCPU.

Code: 0510

Display: FUSER ERROR
Description: Abnormally low heating roller temperature
• The temperature detected by the thermistor /1 remains lower than the specified value for a given period of time or longer.
Remedy: 1 Check the fuser unit for correct installation (whether it is secured in position). 2 Check the connector between fuser unit- PRCB PJ9 for proper connection and correct as necessary. 3 Check the connector between fuser unit- DCPU CN2 for proper connection and correct as necessary. 4 Change fuser unit. 5 Change PRCB. 6 Change DCPU.

Code: 0520

Display: FUSER ERROR
Description: Abnormally high heating roller temperature
• The temperature detected by the thermistor /1 remains higher than the specified value for a given period of time or longer. • The heater lamp remains ON for a given period of time or longer.
Remedy: 1 Check the fuser unit for correct installation (whether it is secured in position). 2 Check the connector between fuser unit- PRCB PJ9 for proper connection and correct as necessary. 3 Check the connector between fuser unit- DCPU CN2 for proper connection and correct as necessary. 4 Change fuser unit. 5 Change PRCB. 6 Change DCPU.

Code: 0F52

Display: TE SENSOR Y
Description: Toner level sensor /Y malfunction
• An error occurs on the toner level sensor for each color.
Remedy: 1 Check the connector between each sensor- PRCB PJ21 for proper connection and correct as necessary. 2 Replace the toner level sensor of the corresponding color. 3 Change PRCB.
Đăng ký nhận bản tin Đăng ký nhận bản tin Đăng ký nhận bản tin Đăng ký nhận bản tin
Đăng ký nhận bản tin
Nhận ưu đãi sớm nhất khi chương trình diễn ra

Đăng ký nhận bản tin

Việc cho phép sử dụng cookie sẽ giúp cải thiện trải nghiệm của bạn trên trang web này. Chính sách cookie