Thương hiệu phân phối chính hãng
Giỏ hàng

Mã lỗi Kyocera FS9130DN — Trang 3/9

Code: 4000

Description: Polygon motor synchronization problem
The polygon motor does not reach the stable speed within 20 s of the START signal turning on.s
Causes: Poor contact in the connector terminals. Defective polygon motor. Defective engine PWB.
Remedy: Poor contact in the connector terminals. Check the connection of connector YC8 on the engine PWB and laser scanner unit, and the continuity across the connector terminals. Repair or replace if necessary. Defective polygon motor. Replace the laser scanner unit. Defective engine PWB. Replace the engine PWB and check for correct operation.

Code: 4010

Description: Polygon motor steady-state problem
The polygon motor rotation is not stable for 20 s after the polygon motor rotation has been stabilized.
Causes: Poor contact in the connector terminals. Defective polygon motor. Defective engine PWB.
Remedy: Poor contact in the connector terminals. Check the connection of connector YC8 on the engine PWB and laser scanner unit, and the continuity across the connector terminals. Repair or replace if necessary. Defective polygon motor. Replace the laser scanner unit. Defective engine PWB. Replace the engine PWB and check for correct operation.

Code: 4200

Description: BD steady-state problem
ASIC detects a BD error A for 2 s after the polygon motor rotation has been stabilized.
Causes: Poor contact in the connector terminals. Defective laser scanner unit. Defective engine PWB.
Remedy: Poor contact in the connector terminals. Check the connection of connector YC8 on the engine PWB and laser scanner unit, and the continuity across the connector terminals. Repair or replace if necessary. Defective laser scanner unit. Replace the laser scanner unit. Defective engine PWB. Replace the engine PWB and check for correct operation.

Code: 5300

Description: Broken cleaning lamp wire
While the cleaning lamp is on, the broken cleaning lamp wire detection signal is detected for 2 s continuously.
Causes: Defective cleaning lamp. Defective engine PWB.
Remedy: Defective cleaning lamp. Replace the cleaning lamp. Defective engine PWB. Replace the engine PWB and check for correct operation.

Code: 6000

Description: Fuser heater brea
Fuser thermistor 1 is detected 40°C/ 104°F below with 10 s continuously during warm-up and ready in.
Causes: Defective fuser heater M or S. Installation defectiveness on fuser thermistor 1. Defective fuser thermostat. Defective PWB.
Remedy: Defective fuser heater M or S. Replace the fuser heater M or S. Installation defectiveness on fuser thermistor 1. Check the mounting state of the fuser thermistor 1. If any problem is found, repair it. Defective fuser thermostat. Replace the fuser thermostat. Defective PWB. Replace the power source PWB or engine PWB and check for correct operation.

Code: 6020

Description: Abnormally high fuser thermistor temperature
Fuser thermistor 1 or 2 is detected 230°C/446°F or more for 40 ms.
Causes: Installation defectiveness on fuser thermistor 1 or 2. Defective fuser thermistor 1 or 2. Defective engine PWB.
Remedy: Installation defectiveness on fuser thermistor 1 or 2. Check the mounting state of the fuser thermistor 1 or 2. If any problem is found, repair it. Defective fuser thermistor 1 or 2. Replace the fuser thermistor 1 or 2. Defective engine PWB. Replace the engine PWB and check for correct operation.

Code: 6030

Description: Fuser thermistor break error
The thermistor break signal is detected continuously for 500 ms.
Causes: Installation defectiveness on fuser thermistor 1 or 2. Defective fuser thermistor 1 or 2. Defective engine PWB.
Remedy: Installation defectiveness on fuser thermistor 1 or 2. Check the mounting state of the fuser thermistor 1 or 2. If any problem is found, repair it. Defective fuser thermistor 1 or 2. Replace the fuser thermistor 1 or 2. Defective engine PWB. Replace the engine PWB and check for correct operation.

Code: 6050

Description: Abnormally low fuser thermistor 3 temperature
Fuser thermistor 1 is detected 100°C/ 212°F less than 1 s continuously during copying.
Causes: Defective fuser heater M or S. Installation defectiveness on fuser thermistor 1. Defective PWB.
Remedy: Defective fuser heater M or S. Replace the fuser heater M or S. Installation defectiveness on fuser thermistor 1. Check the mounting state of the fuser thermistor 1. If any problem is found, repair it. Defective PWB. Replace the power source PWB or engine PWB and check for correct operation.
Đăng ký nhận bản tin Đăng ký nhận bản tin Đăng ký nhận bản tin Đăng ký nhận bản tin
Đăng ký nhận bản tin
Nhận ưu đãi sớm nhất khi chương trình diễn ra

Đăng ký nhận bản tin

Việc cho phép sử dụng cookie sẽ giúp cải thiện trải nghiệm của bạn trên trang web này. Chính sách cookie