Thương hiệu phân phối chính hãng
Giỏ hàng

Mã lỗi Kyocera TASKalfa 181 — Trang 5/6

Code: C3100

Description: Scanner carriage problem
The home position is not correct when the power is turned on or at the start of copying using the table.
Causes: Poor contact in the connector terminals.
Defective home position switch.
Defective scanner motor.
The mirror frame, exposure lamp, or scanner wire is defective.
Defective engine PWB.
Remedy: Poor contact in the connector terminals. Check the connection of connector YC5 on the engine PWB and the connector on the home position switch, and the continuity across the connector terminals. Repair or replace if necessary.
Defective home position switch. Replace the home position switch.
Defective scanner motor. Replace the scanner motor.
The mirror frame, exposure lamp, or scanner wire is defective. Check if the mirror flames and exposure lamp are on the rail. And check the scanner wire winds correctly.
Defective engine PWB. Replace the engine PWB and check for correct operation.

Code: C3200

Description: Exposure lamp problem
Non-lighting of the exposure lamp is detected at the beginning of copying.
Causes: Poor contact in the connector terminals.
Defective exposure lamp.
Incorrect shading position.
Defective PWB.
Remedy: Poor contact in the connector terminals. Check the connection of connector YC16 on the engine PWB and the connector on the inverter PWB, and the continuity across the connector terminals. Repair or replace if necessary.
Defective exposure lamp. Replace the exposure lamp.
Incorrect shading position. Adjust the position of the contact glass (shading plate). If the problem still occurs, replace the home position switch.
Defective PWB. Replace the engine PWB or inverter PWB and check for correct operation.

Code: C3300

Description: AGC problem
After AGC, correct input is not obtained at CCD.
Causes: Poor contact in the connector terminals.
Defective exposure lamp
Defective PWB.
Remedy: Poor contact in the connector terminals. Check the connection of connector YC5 on the main PWB and the connector on the CCD PWB, and the continuity across the connector terminals. Repair or replace if necessary.
Defective exposure lamp. Replace the exposure lamp.
Defective PWB. Replace the main PWB or CCD PWB and check for correct operation.

Code: C4000

Description: Polygon motor synchronization problem
The polygon motor does not reach the stable speed within 20 s of the START signal turning on.
Causes: Poor contact in the connector terminals.
Defective polygon motor.
Defective engine PWB.
Remedy: Poor contact in the connector terminals. Check the connection of connector YC3 on the engine PWB and laser scanner unit, and the continuity across the connector terminals. Repair or replace if necessary.
Defective polygon motor. Replace the laser scanner unit.
Defective engine PWB. Replace the engine PWB and check for correct operation.

Code: C4010

Description: Polygon motor steady-state problem
Stable OFF is detected for 5 s continuously after polygon motor stability.
Causes: Poor contact in the connector terminals.
Defective polygon motor.
Defective engine PWB.
Remedy: Poor contact in the connector terminals. Check the connection of connector YC3 on the engine PWB and laser scanner unit, and the continuity across the connector terminals. Repair or replace if necessary.
Defective polygon motor. Replace the laser scanner unit.
Defective engine PWB. Replace the engine PWB and check for correct operation.

Code: C4200

Description: BD steady-state problem
ASIC detects a BD error for 600 ms after the polygon motor rotation has been stabilized.
Causes: Poor contact in the connector terminals.
Defective laser scanner unit.
Defective engine PWB.
Remedy: Poor contact in the connector terminals. Check the connection of connector YC3 on the engine PWB and laser scanner unit, and the continuity across the connector terminals. Repair or replace if necessary.
Defective laser scanner unit. Replace the laser scanner unit.
Defective engine PWB. Replace the engine PWB and check for correct operation.

Code: C6000

Description: Fuser heater break
The temperature does not reach 70 °C/ 158°F in 15 s before secondary stabilization.
Temperature rise of 1°C/1.8°F does not occur in 5 s before secondary stabilization (except during printing).
Causes: Poor contact in the fuser thermistor connector terminals.
Fuser thermistor installed incorrectly.
Fuser thermostat triggered.
Fuser heater installed incorrectly.
Broken fuser heater wire.
Remedy: Poor contact in the fuser thermistor connector terminals. Reinsert the connector. Also check for continuity within the connector cable. If none, remedy or replace the cable.
Fuser thermistor installed incorrectly. Check and reinstall if necessary.
Fuser thermostat triggered. Check for continuity. If none, replace the fuser thermostat.
Fuser heater installed incorrectly. Check and reinstall if necessary.
Broken fuser heater wire. Check for continuity. If none, replace the fuser heater.

Code: C6020

Description: Abnormally high fuser thermistor temperature
Fuser thermistor is detected 230°C/ 446°F or more for 40 ms
Causes: Shorted thermistor.
Broken heater control circuit on the power source PWB.
Remedy: Shorted thermistor. Measure the resistance. If it is 0 Ω, replace the thermistor.
Broken heater control circuit on the power source PWB. Replace the power source PWB and check for correct operation.
Đăng ký nhận bản tin Đăng ký nhận bản tin Đăng ký nhận bản tin Đăng ký nhận bản tin
Đăng ký nhận bản tin
Nhận ưu đãi sớm nhất khi chương trình diễn ra

Đăng ký nhận bản tin

Việc cho phép sử dụng cookie sẽ giúp cải thiện trải nghiệm của bạn trên trang web này. Chính sách cookie