Description: Fuser heater 2 break Fuser thermistor 2 detected less than 100C/212F for 120 s during driving. Fuser thermistor 2 deduced less than 150C/302F for 300 s during driving. Fuser thermistor 2 deduced less than 100C/212F for 5 s during driving.
Remedy: Defective fuser heater 2. Check for continuity across each heater. If none, replace the fuser unit. Defective fuser thermostat 2. Check for continuity across thermostat. If none, remove the cause and replace the fuser unit. Installation defectiveness on fuser thermistor 2. Measure the resistance. If it is ∞, replace the fuser unit. Defective PWB. Replace the power source PWB or engine PWB and check for correct operation.
Description: Abnormally high fuser thermistor 2 temperature The fuser temperature exceeds 190C/ 374F for 1 s.
Causes: Installation defectiveness on fuser thermistor 2. Defective PWB
Remedy: Installation defectiveness on fuser thermistor 2. Measure the resistance. If it is ∞, replace the fuser unit. Defective PWB. Replace the power source PWB or engine PWB and check for correct operation.
Remedy: Installation defectiveness on fuser thermistor 2. Measure the resistance. If it is ∞, replace the fuser unit. Defective fuser heater 2. Check for continuity across each heater. If none, replace the fuser unit. Defective PWB. Replace the power source PWB or engine PWB and check for correct operation.
Description: Fuser heater 1 edge break During warming up, fuser thermistor 1 does not detect temperature rise of 1C/ 1.8F for 10 s. Fuser thermistor 1 does not reach 90F even after 30 s during warming up.
Remedy: Defective fuser heater 1. Check for continuity across each heater. If none, replace the fuser unit. Defective fuser thermostat 1. Check for continuity across thermostat. If none, remove the cause and replace the fuser unit. Installation defectiveness on fuser thermistor 1. Measure the resistance. If it is ∞, replace the fuser unit. Defective PWB. Replace the power source PWB or engine PWB and check for correct operation.
Description: Abnormally high fuser thermistor 1 edge temperature The fuser temperature exceeds 250C/ 482F for 1 s.
Causes: Installation defectiveness on fuser thermistor 1. Defective PWB.
Remedy: Installation defectiveness on fuser thermistor 1. Measure the resistance. If it is ∞, replace the fuser unit. Defective PWB. Replace the power source PWB or engine PWB and check for correct operation.
Remedy: Defective fuser heater 1. Check for continuity across each heater. If none, replace the fuser unit. Installation defectiveness on fuser thermistor 1. Measure the resistance. If it is ∞, replace the fuser unit. Defective PWB. Replace the power source PWB or engine PWB and check for correct operation.
Description: Zero-cross signal error While fuser heater ON/OFF control is performed, the zero-cross signal is not input within 3 s.
Causes: Poor contact in the connector terminals. Defective PWB.
Remedy: Poor contact in the connector terminals. Check the connection of connector YC4 on the engine PWB and the connector YC10 on the power source PWB, and the continuity across the connector terminals. Repair or replace if necessary. Defective PWB. Replace the engine PWB or power source PWB and check for correct operation.
Description: Fuser unit type mismatch problem Absence of the fuser unit is detected.
Causes: Fuser unit connector inserted incorrectly. Different type of the fuser unit is installed.
Remedy: Fuser unit connector inserted incorrectly. Reinsert the fuser unit connector if necessary. Different type of the fuser unit is installed. Install the correct fuser unit.
Nhận ưu đãi sớm nhất khi chương trình diễn ra
Đăng ký nhận bản tin
Việc cho phép sử dụng cookie sẽ giúp cải thiện trải nghiệm của bạn trên trang web này.
Chính sách cookie
Những cookie này là cần thiết để trang web hoạt động đúng cách.
Những cookie này giúp chúng tôi hiểu cách khách truy cập tương tác với trang web.
Những cookie này được sử dụng để cung cấp quảng cáo cá nhân hóa.