• Code: E320
• Description: 3rd drawer transport jam (Paper not reaching the 2nd drawer feed sensor): The paper does not reach the 2nd drawer feed sensor after it has passed the 3rd drawer feed sensor.
• Remedy: 1. Open the side cover and check if there is any paper in front of the 2nd drawer feed sensor. Remove it if there is. * If the error still occurs, check the following. 2. Is the 2nd drawer feed sensor working? (Perform the input check: 03-[FAX]ON/[1]/[F]) * If it is working properly, proceed to 6. If not, check 3 to 5 below. 3. Check if the connector CN348 on the LGC board is disconnected from the 2nd drawer feed sensor or the harnesses are open circuited. Correct if any. 4. Replace the 2nd drawer feed sensor. 5. Replace the LGC board. 6. Are the lower transport clutches working? (Perform the output check: 03-230, 233) * If they are working properly, proceed to 10. If not, check 7 to 9 below. 7. Check if the connector CN348 on the LGC board is disconnected from the lower transport clutches (high/low) or the harnesses are open circuited. Correct if any. 8. Replace the lower transport clutches (high/low speed). 9. Replace the LGC board. 10.Is the PFP transport clutch working? (Perform the output check: 03-225) * If they are working properly, proceed to 16. If not, check 11 to15 below. 11.Check if the connectors CN349 on the LGC board is disconnected from the PFP transport clutch or the harnesses are open circuited. Check if the connectors CN241 and CN244 on the PFP board are disconnected. Correct if any. 12.Replace the PFP transport clutch. 13.Replace the LGC board. 14.Check the condition of the feed roller, separation roller and pickup roller of each paper source, and replace them if they are worn out. 15.Check the transport roller. Replace it if it is worn out.

• Code: E330
• Description: 4th drawer transport jam (Paper not reaching the registration sensor): The paper does not reach the registration sensor after it has passed the 1st drawer feed sensor.
• Remedy: 1. Open the jam access cover and check if there is any paper in front of the 1st drawer feed sensor. Remove it if there is. * If the error still occurs, check the following. 2. Is the 1st drawer feed sensor working? (Perform the input check: 03-[FAX]ON/[1]/[G]) * If it is working properly, proceed to 6. If not, check 3 to 5 below. 3. Check if the connector CN516 on the PFC board is disconnected from the 1st drawer feed sensor or the harnesses are open circuited. Correct if any. 4. Replace the 1st drawer feed sensor. 5. Replace the PFC board. 6. Is the transport motor-1 working? (Perform the output check: 03-124 or 524) * If it is working properly, proceed to 10. If not, check 7 to 9 below. 7. Check if the connector CN512 on the PFC board is disconnected from the transport motor-1 or the harnesses are open circuited. Correct if any. 8. Replace the transport motor-1. 9. Replace the PFC board. 10.Check the condition of the feed roller, separation roller and pickup roller of each paper source, and replace them if they are worn out. 11.Check the transport roller. Replace it if it is worn out.

• Code: E340
• Description: 4th drawer transport jam (Paper not reaching the 1st drawer feed sensor): The paper does not reach the 1st drawer feed sensor after it has passed the 2nd drawer feed sensor.
• Remedy: 1. Open the jam access cover and check if there is any paper in front of the 1st drawer feed sensor. Remove it if there is. * If the error still occurs, check the following. 2. Is the 1st drawer feed sensor working? (Perform the input check: 03-[FAX]ON/[1]/[G]) * If it is working properly, proceed to 6. If not, check 3 to 5 below. 3. Check if the connector CN512 on the PFC board is disconnected from the registration sensor or the harnesses are open circuited. Correct if any. 4. Replace the 1st drawer feed sensor. 5. Replace the PFC board. 6. Is the transport motor-2 working? (Perform the output check: 03-229, 231) * If it is working properly, proceed to 11. If not, check 7 to 10 below. 7. Check if the connector CN512 on the PFC board is disconnected from the transport motor-2 or the harnesses are open circuited. Correct if any. 8. Replace the transport motor-2. 9. Replace the PFC board. 10.Check the condition of the feed roller, separation roller and pickup roller of each paper source, and replace them if they are worn out. 11.Check the transport roller. Replace it if it is worn out.

• Code: E350
• Description: 4th drawer transport jam (Paper not reaching the 2nd drawer feed sensor): The paper does not reach the 2nd drawer feed sensor after it has passed the 3rd drawer feed sensor.
• Remedy: 1. Open the side cover and check if there is any paper in front of the 2nd drawer feed sensor. Remove it if there is. * If the error still occurs, check the following. 2. Is the 2nd drawer feed sensor working? (Perform the input check: 03-[FAX]ON/[1]/[F]) * If it is working properly, proceed to 6. If not, check 3 to 5 below. 3. Check if the connector CN348 on the LGC board is disconnected from the 2nd drawer feed sensor or the harnesses are open circuited. Correct if any. 4. Replace the 2nd drawer feed sensor. 5. Replace the LGC board. 6. Are the lower transport clutches working? (Perform the output check: 03-230, 233) * If they are working properly, proceed to 10. If not, check 7 to 9 below. 7. Check if the connector CN348 on the LGC board is disconnected from the lower transport clutches (high/low) or the harnesses are open circuited. Correct if any. 8. Replace the lower transport clutches (high/low speed). 9. Replace the LGC board. 10.Is the PFP transport clutch working? (Perform the output check: 03-225) * If they are working properly, proceed to 16. If not, check 11 to15 below. 11.Check if the connectors CN349 on the LGC board is disconnected from the PFP transport clutch or the harnesses are open circuited. Check if the connectors CN241 and CN244 on the PFP board are disconnected. Correct if any. 12.Replace the PFP transport clutch. 13.Replace the LGC board. 14.Check the condition of the feed roller, separation roller and pickup roller of each paper source, and replace them if they are worn out. 15.Check the transport roller. Replace it if it is worn out.

• Code: E360
• Description: 4th drawer transport jam (Paper not reaching the 3rd drawer feed sensor): The paper does not reach the 3rd drawer feed sensor after it has passed the 4th drawer feed sensor.
• Remedy: 1. Open the PFP paper feed cover and check if there is any paper in front of the 3rd drawer feed sensor. Remove it if there is. * If the error still occurs, check the following. 2. Is the 3rd feed sensor working? (Perform the input check: 03-[FAX]OFF/[2]/[D]) * If it is working properly, proceed to 7. If not, check 3 to 6 below. 3. Check if the connectors CN349 on the LGC board is disconnected from the 3rd drawer feed sensor or the harnesses are open circuited. Check if the connectors CN 241 and CN243 on the PFP board are disconnected. Correct if any. 4. Replace the 3rd drawer feed sensor. 5. Replace the LGC board. 6. Is the PFP transport clutch working? (Perform the output check: 03-225) * If it is working properly, proceed to 12. If not, check 8 to 11 below. 7. Check if the connectors CN349 on the LGC board is disconnected from the PFP transport clutch or the harnesses are open circuited. Check if the connectors CN 241 and CN244 on the PFP board are disconnected. Correct if any. 8. Replace the PFP transport clutch. 9. Replace the LGC board. 10.Check the condition of the feed roller, separation roller and pickup roller of each paper source, and replace them if they are worn out. 11.Check the PFP transport roller. Replace it if it is worn out.

• Code: E370
• Description: 3rd drawer misfeeding (Paper not reaching the 3rd drawer transport sensor): Paper fed from the 3rd drawer does not reach the 3rd drawer transport sensor.
• Remedy: 1. Is the 3rd drawer transport sensor working? (Perform the input check: 03-[SCAN]ON/[1]/[B]). * If it is working properly, proceed to 6. If not, check 2 to 5 below. 2. Check if the connector CN505 on the PFC board is disconnected from the 3rd drawer transport sensor or the harnesses are open circuited. Correct if so. 3. Check if the 3rd drawer transport sensor is correctly installed or its detecting element is not damaged or stained. 4. Replace the 3rd drawer transport sensor. 5. Replace the PFC board. 6. Are the 3rd drawer transport clutch and the 3rd drawer feed clutch working? (Perform the output check: 03-252, 03-250.) * If they are working properly, proceed to 9. If not, check 7 to 8 below. 7. Check if the connector CN502 on the PFC board is disconnected from the 3rd drawer transport clutch or the 3rd drawer feed clutch, or the harnesses are open circuited. Correct if so. 8. Replace the 3rd drawer transport clutch or the 3rd drawer feed clutch. 9. Is the feed/transport motor working? (Perform the output check: 03-122.)) * If they are working properly, proceed to 12. If not, check 10 to 11 below. 10.Replace the feed/transport motor. 11.Replace the PFC board. 12.Check if there is any abnormality on the driving section of the feed/transport motor or the roller. Correct if any.

• Code: E380
• Description: 4th drawer misfeeding (Paper not reaching the 4th drawer transport sensor): Paper fed from the 4th drawer does not reach the 4th drawer transport sensor.
• Remedy: 1. Is the 4th drawer transport sensor working? (Perform the input check: 03-[COPY]ON/[5]/[E]). * If it is working properly, proceed to 6. If not, check 2 to 5 below. 2. Check if the connector CN516 on the PFC board is disconnected from the 4th drawer transport sensor or the harnesses are open circuited. Correct if so. 3. Check if the 4th drawer transport sensor is correctly installed or its detecting element is not damaged or stained. 4. Replace the 4th drawer transport sensor. 5. Replace the PFC board. 6. Are the 4th drawer transport clutch and the 4th drawer feed clutch working? (Perform the output check: 03-253, 03-251.) * If they are working properly, proceed to 9. If not, check 7 to 8 below. 7. Check if the connector CN502 on the PFC board is disconnected from the 4th drawer transport clutch or the 4th drawer feed clutch, or the harnesses are open circuited. Correct if so. 8. Replace the 4th drawer transport clutch or the 4th drawer feed clutch. 9. Is the feed/transport motor working? (Perform the output check: 03-122.) * If they are working properly, proceed to 12. If not, check 10 to 11 below. 10.Replace the feed/transport motor. 11.Replace the PFC board. 12.Check if there is any abnormality on the driving section of the feed/transport motor or the roller. Correct if any.

• Code: E3C0
• Description: LCF transport jam (Paper not reaching the registration sensor): Paper fed from the LCF and passed through the 1st drawer feed sensor does not reach the registration sensor.
• Remedy: 1. Open the jam access cover and check if there is any paper in front of the 1st drawer feed sensor. Remove it if there is. * If the error still occurs, check the following. 2. Is the 1st drawer feed sensor working? (Perform the input check: 03-[FAX]ON/[1]/[G]) * If it is working properly, proceed to 6. If not, check 3 to 5 below. 3. Check if the connector CN516 on the PFC board is disconnected from the 1st drawer feed sensor or the harnesses are open circuited. Correct if any. 4. Replace the 1st drawer feed sensor. 5. Replace the PFC board. 6. Is the transport motor-1 working? (Perform the output check: 03-124 or 524) * If it is working properly, proceed to 10. If not, check 7 to 9 below. 7. Check if the connector CN512 on the PFC board is disconnected from the transport motor-1 or the harnesses are open circuited. Correct if any. 8. Replace the transport motor-1. 9. Replace the PFC board. 10.Check the condition of the feed roller, separation roller and pickup roller of each paper source, and replace them if they are worn out. 11.Check the transport roller. Replace it if it is worn out.