Thương hiệu phân phối chính hãng
Giỏ hàng

Mã lỗi Lexmark C544n — Trang 2/22

Code: 106.09

Description: Service Yellow Printhead
SOS/EOS measurement did not complete.
Remedy: 1 Turn the printer off, and remove the rear shield. See “Rear shield removal”. Check the cable at JMIRR1 for proper connection to the controller board, the printhead cable for pinch points, and the cable or connector for any other damage. Is the cable damaged? Replace the printhead. See “Printhead removal”. Go to step 2.
2 Turn the printer on, and then wait until the printer posts an error. Using a voltmeter, check the following values at JMIRR1: Are the values approximately correct? Replace the controller board See “Controller board removal”. Replace the printhead. See “Printhead removal”.

Code: 106.10

Description: Service Yellow Printhead
Bad SOS/EOS measurement.
Remedy: 1 Turn the printer off, and remove the rear shield. See “Rear shield removal”. Check the cable at JMIRR1 for proper connection to the controller board, the printhead cable for pinch points, and the cable or connector for any other damage. Is the cable damaged? Replace the printhead. See “Printhead removal”. Go to step 2.
2 Turn the printer on, and then wait until the printer posts an error. Using a voltmeter, check the following values at JMIRR1: Are the values approximately correct? Replace the controller board See “Controller board removal”. Replace the printhead. See “Printhead removal”.

Code: 106.11

Description: Service Yellow Printhead
Failure writing data tot he printhead.
Remedy: 1 Turn the printer off, and remove the rear shield. See “Rear shield removal”. Check the cable at JMIRR1 for proper connection to the controller board, the printhead cable for pinch points, and the cable or connector for any other damage. Is the cable damaged? Replace the printhead. See “Printhead removal”. Go to step 2.
2 Turn the printer on, and then wait until the printer posts an error. Using a voltmeter, check the following values at JMIRR1: Are the values approximately correct? Replace the controller board See “Controller board removal”. Replace the printhead. See “Printhead removal”.

Code: 106.12

Description: Service Yellow Printhead
Failure reading data from the printhead.
Remedy: 1 Turn the printer off, and remove the rear shield. See “Rear shield removal”. Check the cable at JMIRR1 for proper connection to the controller board, the printhead cable for pinch points, and the cable or connector for any other damage. Is the cable damaged? Replace the printhead. See “Printhead removal”. Go to step 2.
2 Turn the printer on, and then wait until the printer posts an error. Using a voltmeter, check the following values at JMIRR1: Are the values approximately correct? Replace the controller board See “Controller board removal”. Replace the printhead. See “Printhead removal”.

Code: 106.13

Description: Service Yellow Printhead
Printhead declared error.
Remedy: 1 Turn the printer off, and remove the rear shield. See “Rear shield removal”. Check the cable at JMIRR1 for proper connection to the controller board, the printhead cable for pinch points, and the cable or connector for any other damage. Is the cable damaged? Replace the printhead. See “Printhead removal”. Go to step 2.
2 Turn the printer on, and then wait until the printer posts an error. Using a voltmeter, check the following values at JMIRR1: Are the values approximately correct? Replace the controller board See “Controller board removal”. Replace the printhead. See “Printhead removal”.

Code: 106.xx

Description: Service Yellow Printhead
Yellow printhead error.
Remedy: 1 Turn the printer off, and remove the rear shield. See “Rear shield removal”. Check the cable at JMIRR1 for proper connection to the controller board, the printhead cable for pinch points, and the cable or connector for any other damage. Is the cable damaged? Replace the printhead. See “Printhead removal”. Go to step 2.
2 Turn the printer on, and then wait until the printer posts an error. Using a voltmeter, check the following values at JMIRR1: Are the values approximately correct? Replace the controller board See “Controller board removal”. Replace the printhead. See “Printhead removal”.

Code: 107.01

Description: Service Cyan Printhead
The cyan printhead lost HSYNC.
Remedy: 1 Turn the printer off, and remove the rear shield. See “Rear shield removal”. Check the cable at JMIRR1 for proper connection to the controller board, the printhead cable for pinch points, and the cable or connector for any other damage. Is the cable damaged? Replace the printhead. See “Printhead removal”. Go to step 2.
2 Turn the printer on, and then wait until the printer posts an error. Using a voltmeter, check the following values at JMIRR1: Are the values approximately correct? Replace the controller board See “Controller board removal”. Replace the printhead. See “Printhead removal”.

Code: 107.02

Description: Service Cyan Printhead
The cyan printhead failed to complete servo.
Remedy: 1 Turn the printer off, and remove the rear shield. See “Rear shield removal”. Check the cable at JMIRR1 for proper connection to the controller board, the printhead cable for pinch points, and the cable or connector for any other damage. Is the cable damaged? Replace the printhead. See “Printhead removal”. Go to step 2.
2 Turn the printer on, and then wait until the printer posts an error. Using a voltmeter, check the following values at JMIRR1: Are the values approximately correct? Replace the controller board See “Controller board removal”. Replace the printhead. See “Printhead removal”.
Đăng ký nhận bản tin Đăng ký nhận bản tin Đăng ký nhận bản tin Đăng ký nhận bản tin
Đăng ký nhận bản tin
Nhận ưu đãi sớm nhất khi chương trình diễn ra

Đăng ký nhận bản tin

Việc cho phép sử dụng cookie sẽ giúp cải thiện trải nghiệm của bạn trên trang web này. Chính sách cookie