Description: Service Yellow Printhead SOS/EOS measurement did not complete.
Remedy: 1 Turn the printer off, and remove the rear shield. See “Rear shield removal”. Check the cable at JMIRR1 for proper connection to the controller board, the printhead cable for pinch points, and the cable or connector for any other damage. Is the cable damaged? Replace the printhead. See “Printhead removal”. Go to step 2. 2 Turn the printer on, and then wait until the printer posts an error. Using a voltmeter, check the following values at JMIRR1: Are the values approximately correct? Replace the controller board See “Controller board removal”. Replace the printhead. See “Printhead removal”.
Description: Service Yellow Printhead Bad SOS/EOS measurement.
Remedy: 1 Turn the printer off, and remove the rear shield. See “Rear shield removal”. Check the cable at JMIRR1 for proper connection to the controller board, the printhead cable for pinch points, and the cable or connector for any other damage. Is the cable damaged? Replace the printhead. See “Printhead removal”. Go to step 2. 2 Turn the printer on, and then wait until the printer posts an error. Using a voltmeter, check the following values at JMIRR1: Are the values approximately correct? Replace the controller board See “Controller board removal”. Replace the printhead. See “Printhead removal”.
Description: Service Yellow Printhead Failure writing data tot he printhead.
Remedy: 1 Turn the printer off, and remove the rear shield. See “Rear shield removal”. Check the cable at JMIRR1 for proper connection to the controller board, the printhead cable for pinch points, and the cable or connector for any other damage. Is the cable damaged? Replace the printhead. See “Printhead removal”. Go to step 2. 2 Turn the printer on, and then wait until the printer posts an error. Using a voltmeter, check the following values at JMIRR1: Are the values approximately correct? Replace the controller board See “Controller board removal”. Replace the printhead. See “Printhead removal”.
Description: Service Yellow Printhead Failure reading data from the printhead.
Remedy: 1 Turn the printer off, and remove the rear shield. See “Rear shield removal”. Check the cable at JMIRR1 for proper connection to the controller board, the printhead cable for pinch points, and the cable or connector for any other damage. Is the cable damaged? Replace the printhead. See “Printhead removal”. Go to step 2. 2 Turn the printer on, and then wait until the printer posts an error. Using a voltmeter, check the following values at JMIRR1: Are the values approximately correct? Replace the controller board See “Controller board removal”. Replace the printhead. See “Printhead removal”.
Description: Service Yellow Printhead Printhead declared error.
Remedy: 1 Turn the printer off, and remove the rear shield. See “Rear shield removal”. Check the cable at JMIRR1 for proper connection to the controller board, the printhead cable for pinch points, and the cable or connector for any other damage. Is the cable damaged? Replace the printhead. See “Printhead removal”. Go to step 2. 2 Turn the printer on, and then wait until the printer posts an error. Using a voltmeter, check the following values at JMIRR1: Are the values approximately correct? Replace the controller board See “Controller board removal”. Replace the printhead. See “Printhead removal”.
Description: Service Yellow Printhead Yellow printhead error.
Remedy: 1 Turn the printer off, and remove the rear shield. See “Rear shield removal”. Check the cable at JMIRR1 for proper connection to the controller board, the printhead cable for pinch points, and the cable or connector for any other damage. Is the cable damaged? Replace the printhead. See “Printhead removal”. Go to step 2. 2 Turn the printer on, and then wait until the printer posts an error. Using a voltmeter, check the following values at JMIRR1: Are the values approximately correct? Replace the controller board See “Controller board removal”. Replace the printhead. See “Printhead removal”.
Description: Service Cyan Printhead The cyan printhead lost HSYNC.
Remedy: 1 Turn the printer off, and remove the rear shield. See “Rear shield removal”. Check the cable at JMIRR1 for proper connection to the controller board, the printhead cable for pinch points, and the cable or connector for any other damage. Is the cable damaged? Replace the printhead. See “Printhead removal”. Go to step 2. 2 Turn the printer on, and then wait until the printer posts an error. Using a voltmeter, check the following values at JMIRR1: Are the values approximately correct? Replace the controller board See “Controller board removal”. Replace the printhead. See “Printhead removal”.
Description: Service Cyan Printhead The cyan printhead failed to complete servo.
Remedy: 1 Turn the printer off, and remove the rear shield. See “Rear shield removal”. Check the cable at JMIRR1 for proper connection to the controller board, the printhead cable for pinch points, and the cable or connector for any other damage. Is the cable damaged? Replace the printhead. See “Printhead removal”. Go to step 2. 2 Turn the printer on, and then wait until the printer posts an error. Using a voltmeter, check the following values at JMIRR1: Are the values approximately correct? Replace the controller board See “Controller board removal”. Replace the printhead. See “Printhead removal”.
Nhận ưu đãi sớm nhất khi chương trình diễn ra
Đăng ký nhận bản tin
Việc cho phép sử dụng cookie sẽ giúp cải thiện trải nghiệm của bạn trên trang web này.
Chính sách cookie
Những cookie này là cần thiết để trang web hoạt động đúng cách.
Những cookie này giúp chúng tôi hiểu cách khách truy cập tương tác với trang web.
Những cookie này được sử dụng để cung cấp quảng cáo cá nhân hóa.