Thương hiệu phân phối chính hãng
Giỏ hàng

Mã lỗi OKI CX4545 MFP — Trang 11/18

Code: CC52

Description: Skew adjustment motor (M1) abnormality
Causes: Skew home position sensor (S2) Skew adjustment motor (M1) Hole punch control PC board (HP)
Remedy: MJ-1101/1106 (When MJ-6103 is installed) Transport path If there is any paper remaining on the transport path, remove the paper. Skew adjustment motor (M1) • If there is mechanical problem when the skew adjustment motor (M1) is rotated, fix the mechanism. • Check the connectors and harnesses between the hole punch control PC board (HP) and skew adjustment motor (M1). Skew home position sensor (S2) • Sensor check • Harness check

Code: CC61

Description: Punch motor (M3) home position detection error.
Causes: Punch home position sensor (S4) Punch motor (M3) Hole punch control PC board (HP)
Remedy: MJ-1101/1106 (When MJ-6103 is installed) Transport path If there is any paper remaining on the transport path, remove the paper. Punch motor (M3) • If there is mechanical problem when the punch motor (M3) is rotated, fix the mechanism. • Check the connectors and harnesses between the hole punch control PC board (HP) and punch motor (M3). Punch home position sensor (S4) • Sensor check • Harness check

Code: CC71

Description: Punch ROM checksum error. Punch ROM checksum error: Abnormality of checksum value on Hole punch controller PC board is detected when the power is turned on.
Causes: Hole punch control PC board (HP)
Remedy: MJ-1101/1106 (When MJ-6103 is installed) Hole punch control PC board (HP) Board check

Code: CC72

Description: Punch RAM read/write error. Punch RAM read/write error: Abnormality of checksum value on Hole punch controller PC board is detected when the power is turned on.
Causes: Hole punch control PC board (HP)
Remedy: MJ-1101/1106 (When MJ-6103 is installed) Hole punch control PC board (HP) Board check

Code: CC80

Description: Rear alignment motor abnormality. Rear alignment motor abnormality: The rear alignment motor is not rotating or the rear alignment plate is not moving normally.
Causes: Rear alignment motor (M10) Finisher control PC board
Rear alignment motor (M6) Finisher control PC board
Remedy: MJ-1101 Rear alignment plate If there is mechanical problem when the rear alignment plate is moved, fix the mechanism. Rear alignment motor (M10) Check the connectors and harnesses between the rear alignment motor (M10) and the finisher control PC board (CN10).
MJ-1106 Rear alignment plate If there is mechanical problem when the rear alignment plate is moved, fix the mechanism. Rear alignment motor (M6) Check the connectors and harnesses between the rear alignment motor (M6) and the finisher control PC board (CN17).

Code: CC90

Description: Tray shift motor abnormality. Tray shift motor abnormality: The tray shift motor is not rotating or the stack tray is not moving normally.
Causes: Tray clock sensor (SR9) Tray lower limit sensor (SR5) Tray 500 sensor (SR4) Sensor controller PC board Finisher control PC board Tray shift motor (M2)
Remedy: MJ-1031 Tray shift motor (M2) Check the connectors and harnesses between the finisher controller PC board and tray shift motor (M2). Stack tray Check if the front and rear sides of the stack tray are leveled. Tray clock sensor (SR9) Sensor check Tray lower limit sensor (SR5) Sensor check Tray 500 sensor (SR4) Sensor check Tray safety switch (SW2) Switch check Finisher controller PC board Check if the voltage between the pins J114-1 and J114-2 on the finisher controller PC board becomes 24V when the tray shift motor starts rotating.

Code: CCB0

Description: Offset motor abnormality.
Causes: Offset HP sensor (SR1) Offset motor (M5) Finisher control PC board
Remedy: Offset HP sensor (SR1) Check the connectors and harnesses between the offset HP sensor (SR1) and the connector J104 on the finisher controller PC board. Offset motor (M5) Check the connectors and harnesses between the offset motor (M5) and the connector J107 on the finisher controller PC board.

Code: CCF1

Description: Tray safety switch abnormality. Tray safety switch abnormality: • The tray safety switch turned on during tray operation (moving up or down). • The tray operated with the tray safety switch turned on.
Causes: Tray safety switch (SW2) Stack tray shift motor (M2) Finisher control PC board
Remedy: MJ-1031 Tray safety switch (SW2) Check the connectors and harnesses between the tray safety switch (SW2) and the connector J110 on the finisher controller PC board. Stack tray shift motor (M2) Check the connectors and harnesses between the stack tray shift motor (M2) and the connector J114 on the finisher controller PC board.
Đăng ký nhận bản tin Đăng ký nhận bản tin Đăng ký nhận bản tin Đăng ký nhận bản tin
Đăng ký nhận bản tin
Nhận ưu đãi sớm nhất khi chương trình diễn ra

Đăng ký nhận bản tin

Việc cho phép sử dụng cookie sẽ giúp cải thiện trải nghiệm của bạn trên trang web này. Chính sách cookie