Thương hiệu phân phối chính hãng
Giỏ hàng

Mã lỗi Ricoh Aficio 2045 — Trang 5/18

Code: 450

Description: Feed Development Motor Error
The PLL lock signal remains LOW for 2 s while the feed development motor is operating.
Causes: • Motor lock caused by overload. • Motor driver defective.

Code: 490

Description: Exhaust fan motor lock
An exhaust fan motor lock signal is not detected within 5 seconds after the exhaust fan motor turns on
Causes: • Too much load on the drive mechanism • Exhaust fan motor defective or a loose object is interfering with the fan • Poor fan motor connector connection

Code: 492

Description: Cooling fan motor lock
A cooling fan motor lock signal is not detected within 5 seconds after the cooling fan motor turns on.
Causes: • Too much load on the drive mechanism • Cooling fan motor defective or a loose object is interfering with the fan • Poor fan motor connector connection

Code: 501

Description: 1st tray lift malfunction
The paper height sensor is not activated after the tray lift motor has been on for 10 seconds. If the main power switch is turned on when the paper is already at the feed height, the paper height position is detected again. At this time, the paper height sensor should de-activate within 5 seconds after the paper bottom plate starts to drop. If it does not deactivate within 5 s four times consecutively, a message will prompt the user to reset Tray 1. After two attempts to release the error by re-setting the paper tray, if this does not solve the problem then this SC is displayed.
Causes: • Lift motor malfunction or disconnected • Height sensor abnormal, or connector loose • Loose paper or object between the tray and motor • Pick-up arm malfunction

Code: 502

Description: 2nd tray lift malfunction
The paper height sensor is not activated after the tray lift motor has been on for 10 seconds. If the main power switch is turned on when the paper is already at the feed height, the paper height position is detected again. At this time, the paper height sensor should de-activate within 5 seconds after the paper bottom plate starts to drop. If it does not deactivate within 5 s four times consecutively, a message will prompt the user to reset Tray 2. After two attempts to re-set the paper tray, if this does not solve the problem then this SC is displayed.
Causes: • Lift motor abnormal or disconnected • Height sensor defective or disconnected • Loose paper or object between the tray and motor • Pick-up arm malfunction

Code: 503

Description: 3rd tray lift malfunction (optional paper tray unit)
The paper height sensor is not activated after the tray lift motor has been on for 13 seconds. If the main power switch is turned on when the paper is already at the feed height, the paper height position is detected again. At this time, the paper height sensor should de-activate within 5 seconds after the paper bottom plate starts to drop. If it does not deactivate within 5 s four times consecutively, the tray lift motor halts. After two attempts to re-set the paper tray, if this does not solve the problem, then this SC is displayed and tray control halts.
Causes: • Tray lift motor defective or disconnected • Height sensor defective or disconnected

Code: 504

Description: 4th tray lift malfunction (optional paper tray unit)
The paper height sensor is not activated after the tray lift motor has been on for 13 seconds. If the main power switch is turned on when the paper is already at the feed height, the paper height position is detected again. At this time, the paper height sensor should de-activate within 5 seconds after the paper bottom plate starts to drop. If it does not deactivate within 5 s four times consecutively, the tray lift motor halts. After two attempts to re-set the paper tray, if this does not solve the problem, then this SC is displayed and tray control halts.
Causes: • Tray lift motor defective or disconnected • Height sensor defective or disconnected

Code: 506

Description: Paper tray unit main motor lock (optional paper tray)
A main motor lock signal is detected for more than 50 ms during rotation.
Causes: • Paper tray unit main motor defective • Paper tray unit main motor connection loose • Too much load on the drive mechanism
Đăng ký nhận bản tin Đăng ký nhận bản tin Đăng ký nhận bản tin Đăng ký nhận bản tin
Đăng ký nhận bản tin
Nhận ưu đãi sớm nhất khi chương trình diễn ra

Đăng ký nhận bản tin

Việc cho phép sử dụng cookie sẽ giúp cải thiện trải nghiệm của bạn trên trang web này. Chính sách cookie