Thương hiệu phân phối chính hãng
Giỏ hàng

Mã lỗi Ricoh Aficio MPC401SP — Trang 10/25

Code: 545

Description: Heating roller fusing lamp consecutive full power 1 When the fusing unit is not running in the ready condition, the heating roller fusing lamp keeps on full power for 8 seconds.
Causes: • Broken heating roller fusing lamp
Remedy: Related SC code: SC 555 • Replace the heating roller fusing lamp. • Replace the PSU.

Code: 547-01

Description: Zero cross error (Fusing relay short) • The zero cross signal is detected three times even though the heater relay is off when turning on the main power. • The zero cross signal is not detected for 3 seconds even though the heater relay is on after turning on the main power or closing the front door. • The detection error occurs twice or more in the 11 zero cross signal detections. This error is defined when the detected zero cross signal is less than 45.
Causes: • Defective fusing lamp relay • Defective fusing lamp relay circuit
Remedy: • Replace the PSU. • Replace the BCU.

Code: 547-02

Description: Zero cross error (Fusing relay open) • The zero cross signal is detected three times even though the heater relay is off when turning on the main power. • The zero cross signal is not detected for 2 seconds even though the heater relay is on after turning on the main power or closing the front door. • The detection error occurs twice or more in the 11 zero cross signal detections. This error is defined when the detected zero cross signal is less than 45.
Causes: • Defective fusing lamp relay • Defective fusing lamp relay circuit • Short 24VS fuse
Remedy: • Replace the 24VS fuse (FU3/FU4). • Replace the PSU. • Replace the BCU.

Code: 547-03

Description: Zero cross error • The zero cross signal is detected three times even though the heater relay is off when turning on the main power. • The zero cross signal is not detected for 2 seconds even though the heater relay is on after turning on the main power or closing the front door. • The detection error occurs twice or more in the 11 zero cross signal detections. This error is defined when the detected zero cross signal is less than 45.
Causes: • Unstable power supply
Remedy: • Check the power supply source.

Code: 551

Description: Heating roller thermistor error The temperature at the end of the heating roller measured by the heating roller thermistor does not reach 0°C for 7 seconds.
Causes: • Loose connection of pressure roller thermistor • Defective heating roller thermistor
Remedy: Related SC code: SC 541 • Check that the heating roller thermistor is firmly connected. • Replace the heating roller thermistor.

Code: 552

Description: Heating roller warm-up error 2 • The heating roller temperature does not reach 80°C for 20 seconds. • The temperature at the end of the heating roller does not reach the ready temperature for 89 seconds .
Causes: • Defective heating roller thermistor
Remedy: Related SC code: SC 542 • Check if the heating roller thermistor is firmly connected.

Code: 553

Description: Heating roller fusing lamp overheat 2 (software error) The temperature detected by the heating roller thermistor stays at 230°C or more for 1 second.
Causes: • Defective PSU • Defective IPU • Defective BCU
Remedy: • Replace the PSU. • Replace the IPU. • Replace the BCU.

Code: 554

Description: Heating roller fusing lamp overheat 2 (hardware error) The temperature detected by the heating roller thermistor reaches 250°C or more.
Causes: • Defective PSU • Defective IPU • Defective BCU • Defective fusing control system
Remedy: • Replace the PSU. • Replace the IPU. • Replace the BCU.
Đăng ký nhận bản tin Đăng ký nhận bản tin Đăng ký nhận bản tin Đăng ký nhận bản tin
Đăng ký nhận bản tin
Nhận ưu đãi sớm nhất khi chương trình diễn ra

Đăng ký nhận bản tin

Việc cho phép sử dụng cookie sẽ giúp cải thiện trải nghiệm của bạn trên trang web này. Chính sách cookie