• Code: 715-003
• Description: ADF transport motor driver error
  The protection circuit of the motor driver stops the motor operation due to over current, high temperature or driver open.
• Causes: Turn the machine off and on.
• Remedy:

• Code: 715-004
• Description: ADF exit motor driver error (one-pass through model only)
  The protection circuit of the motor driver stops the motor operation due to over current, high temperature or driver open.
• Causes: Turn the machine off and on.
• Remedy:

• Code: 715-006
• Description: ADF exit motor driver error (auto reverse model only)
  The protection circuit of the motor driver stops the motor operation due to over current, high temperature or driver open.
• Causes: Turn the machine off and on.
• Remedy:

• Code: 721
• Description: Finisher jogger motor error
  The jogger fences move out of the home position but the HP sensor output does not change within the specified number of pulses. The 1st failure issues an original jam message, and the 2nd failure issues this SC code.
• Causes: • Jogger HP sensor disconnected, defective • Jogger motor disconnected, defective • Jogger motor overloaded due to obstruction • Finisher main board and jogger motor
• Remedy: 1. Check the connections and cables for the components mentioned above. 2. Check for blockages in the jogger motor mechanism. 3. Replace the jogger HP sensor and/or jogger motor. 4. Replace the finisher main board.

• Code: 723
• Description: Stack feed-out motor error
  • The stack feed-out HP sensor does not detect the home position of the stack feed-out belt 3000ms after the stack feed-out belt has moved to its home position. • The stack feed-out HP sensor does not turn off 200 ms after the stack feed-out belt has moved from its home position. • The 1st detection failure causes a jam error, and the 2nd failure causes this SC code.
• Causes: • Defective stack feed-out HP sensor • Overload on the stack feed-out motor • Defective stack feed-out motor • Defective main board • Disconnected or defective harness
• Remedy: 1. Check the connections and cables for the components mentioned above. 2. Check for blockages in the stack feed-out motor mechanism. 3. Replace the stack feed-out HP sensor and/or stack feed-out motor. 4. Replace the finisher main board.

• Code: 725
• Description: Finisher exit guide plate motor error
  After moving away from the guide plate position sensor, the exit guide is not detected at the home position within the prescribed time. The 1st detection failure issues a jam error, and the 2nd failure issues this SC code.
• Causes: • Guide plate motor disconnected, defective • Guide plate motor overloaded due to obstruction • Guide plate position sensor disconnected, defectiveon.
• Remedy: 1. Check the connections and cables for the components mentioned above. 2. Check for blockages in the guide plate motor mechanism. 3. Replace the guide plate position sensor and/or guide plate motor 4. Replace the finisher main board.

• Code: 730
• Description: Finisher Tray 1 shift motor error
  The shift roller HP sensor of the upper tray does not activate within the prescribed time after the shift tray starts to move toward or away from the home position. The 1st detection failure issues a jam error, and the 2nd failure issues this SC code.
• Causes: • Shift tray HP sensor of the upper tray disconnected, defective • Shift tray motor of the upper tray is disconnected, defective • Shift tray motor of the upper tray overloaded due to obstruction
• Remedy: 1. Check the connections and cables for the components mentioned above. 2. Check for blockages in shift motor mechanism. 3. Replace the shift tray HP sensor and/or shift motor 4. Replace the finisher main board.

• Code: 740
• Description: Finisher corner stapler motor error
  The 1st detection failure issues a jam error, and the 2nd failure issues this SC code. For the 2000/3000-sheet (booklet) finisher • Staple movement is not finished after a certain time. For the 1000-sheet finisher • The stapler motor does not switch off within the prescribed time after operating. • The HP sensor of the staple unit does not detect the home position after the staple unit moves to its home position. • The HP sensor of the staple unit detects the home position after the staple unit moves from its home position.
• Causes: • Staple jam • Motor overload • Defective stapler motor
• Remedy: 1. Check the connections and cables for the components mentioned above. 2. Replace the HP sensor and/or stapler motor 3. Replace the finisher main board.