Thương hiệu phân phối chính hãng
Giỏ hàng

Mã lỗi Ricoh Aficio MPC4502 — Trang 13/30

Code: 534-02

Description: Tube cooling fan error
The machine does not detect the fan motor lock signal for 100 ms while the third duct fan or tube cooling fan turns on.
Causes: • Disconnected harness • Overload on the third duct fan motor or tube cooling fan motor • Defective third duct motor or tube cooling motor • Defective IOB
Remedy: 1. Check or replace the harness. 2. Replace the third duct fan or tube cooling fan. 3. Replace the IOB.

Code: 535

Description: Paper exit fan error
The machine does not detect the fan motor lock signal for 100 ms while the paper exit fan turns on.
Causes: • Disconnected harness • Overload on the paper exit fan motor • Defective paper exit motor • Defective IOB
Remedy: 1. Check or replace the harness. 2. Replace the paper exit fan. 3. Replace the IOB.

Code: 538

Description: AC controller board fan error
The machine does not detect the fan motor lock signal for 100 ms while the AC controller board fan turns on.
Causes: • Disconnected harness • Overload on the AC controller board fan motor • Defective AC controller board fan motor • Defective IOB
Remedy: 1. Check or replace the harness. 2. Replace the AC controller board fan. 3. Replace the IOB.

Code: 540

Description: Fusing/Paper exit motor error
The IOB does not receive the lock signal 100 ms after turning on the fusing/ paper exit motor.
Causes: • Motor overload • Defective fusing/paper exit motor • Shorted +24V fuse on the PSU
Remedy: 1. Check or replace the harness. 2. Replace the fusing/paper exit motor. 3. Replace the +24V fuse on the PSU.

Code: 541

Description: Heating roller thermopile error
The temperature detected by the heating roller thermopile does not reach 0°C for 6 seconds.
Causes: • Loose connection of the heating roller thermopile • Defective heating roller thermopile • Defective thermopile
Remedy: 1. Check if the heating roller thermopile is firmly connected. 2. Replace the heating roller thermopile.

Code: 542

Description: Heating roller warm-up error 1
• The heating roller temperature does not reach 80°C for 20 seconds after the inverter turned on. • The center temperature of the heating roller does not reach the ready temperature for 90 seconds after the fusing lamp turned on.
Causes: • Dirty or defective thermopile
Remedy: 1. Check if the heating roller thermopile is firmly connected. 2. Replace the thermopile.

Code: 543

Description: Heating roller overheat: Center (software error)
The detected fusing temperature stays at 215°C for 1 second for 10 consecutive times.
Causes: • Defective AC controller board • Defective IOB • Defective IPU
Remedy: 1. Replace the AC controller board. 2. Replace the IOB. 3. Replace the IPU.

Code: 544

Description: Heating roller overheat: Center (hardware error)
During stand-by mode or a print job, the detected heating roller temperature reaches 220°C.
Causes: • Defective AC controller board • Defective IOB • Defective IPU • Defective fusing control system
Remedy: 1. Replace the AC controller board. 2. Replace the IOB. 3. Replace the IPU. 4. Replace the fusing unit and reset the counter of the fusing unit using SP3-902-014. Important: The fusing unit cannot be used because an abnormal high temperature was detected. After this SC occurs, the counter reset of the fusing unit should be done manually using SP3-902-014 because the counter reset is not done automatically.
Đăng ký nhận bản tin Đăng ký nhận bản tin Đăng ký nhận bản tin Đăng ký nhận bản tin
Đăng ký nhận bản tin
Nhận ưu đãi sớm nhất khi chương trình diễn ra

Đăng ký nhận bản tin

Việc cho phép sử dụng cookie sẽ giúp cải thiện trải nghiệm của bạn trên trang web này. Chính sách cookie