Thương hiệu phân phối chính hãng
Giỏ hàng

Mã lỗi Ricoh Aficio MPC5502 — Trang 14/30

Code: 545

Description: Fusing Heater error: Center
The fusing heater keeps full power for 23 seconds or more.
Causes: • Defective thermistors • Disconnected cables
Remedy: 1. Replace the thermistors. 2. Check and replace the cables.

Code: 547

Description: Zero cross error
• The zero cross signal is detected three times even though the heater relay is off when turning on the main power. • The zero cross signal is not detected for 3 seconds even though the heater relay is on after turning on the main power or closing the front door. • The detection error occurs twice or more in the 11 zero cross signal detections. This error is defined when the detected zero cross signal is 39 or less.
Causes: • Defective fusing relay • Defective fusing relay circuit • Shorted +24V fuse on the AC controller board. • Unstable power supply
Remedy: 1. Check the power supply source. 2. Replace the +24V fuse on the AC controller board. 3. Replace the PSU

Code: 549

Description: Fusing heater connection error
The heating roller rotation sensor detects the target temperature as 50°C for 5 seconds or more after the fusing/paper exit motor has turned on.
Causes: • Broken heater cables • Defective connectors
Remedy: 1. Check the cable connection. 2. Replace the heater cables.

Code: 551

Description: Heating roller thermistor error
The temperature at the end of the heating roller measured by the heating roller thermistor does not reach 0°C for 7 seconds.
Causes: • Loose connection of pressure roller thermistor • Defective heating roller thermistor
Remedy: 1. Check that the heating roller thermistor is firmly connected. 2. Replace the heating roller thermistor.

Code: 552

Description: Heating roller warm-up error 2
• The heating roller temperature does not reach 80°C for 20 seconds after the inverter turned on. • The temperature at the end of the heating roller does not reach the ready temperature for 89 seconds after the fusing lamp turned on.
Causes: • Defective heating roller thermistor • Defective inverter
Remedy: 1. Check if the heating roller thermistor is firmly connected. 2. Replace the inverter.

Code: 553

Description: Heating roller overheat: End (software error)
The detected heating roller temperature stays at 215°C or more for 1 second for 10 consecutive times.
Causes: • Defective AC controller board • Defective IOB • Defective IPU
Remedy: 1. Replace the AC controller board. 2. Replace the IOB. 3. Replace the IPU.

Code: 554

Description: Heating roller overheat: End (hardware error)
The heating roller thermistor detects 220°C or more.
Causes: • Defective AC controller board • Defective IOB • Defective IPU • Defective fusing control systemd
Remedy: 1. Replace the AC controller board. 2. Replace the IOB. 3. Replace the IPU.

Code: 555

Description: Fusing Heater error: End
The fusing heater keeps full power for 19 seconds or more.
Causes: • Defective thermistors • Disconnected cables
Remedy: 1. Replace the thermistors. 2. Check and replace the cables.
Đăng ký nhận bản tin Đăng ký nhận bản tin Đăng ký nhận bản tin Đăng ký nhận bản tin
Đăng ký nhận bản tin
Nhận ưu đãi sớm nhất khi chương trình diễn ra

Đăng ký nhận bản tin

Việc cho phép sử dụng cookie sẽ giúp cải thiện trải nghiệm của bạn trên trang web này. Chính sách cookie