• Code: SC720-74
• Description: Shift Jogger Retreat Motor Error (2K/3K sheet finisher)
• Causes: • Motor defective • Connector disconnected • Overload • Encoder defective (*SC720-25 only) • Home position sensor defective
• Remedy: • Check the motor • Check the home position sensor connection • Replace the motor • Replace the home position sensor • Replace the controller

• Code: SC720-75
• Description: Reverse Roller Rocking Motor Error (2K/3K sheet finisher)
• Causes: • Motor defective • Connector disconnected • Overload • Home position sensor defective
• Remedy: • Check the motor • Check the home position sensor connection • Replace the motor • Replace the home position sensor • Replace the controller

• Code: SC720-77
• Description: Edge Guide Motor Error (2K/3K sheet finisher)
• Causes: • Motor defective • Connector disconnected • Overload • Encoder defective (*SC720-25 only) • Home position sensor defective
• Remedy: • Check the motor • Check the home position sensor connection • Replace the motor • Replace the home position sensor • Replace the controller

• Code: SC720-78
• Description: Rear End Press Motor Error (2K/3K sheet finisher)
• Causes: • Motor defective • Connector disconnected • Overload • Home position sensor defective
• Remedy: • Check the motor • Check the home position sensor connection • Replace the motor • Replace the home position sensor • Replace the controller

• Code: SC721-03
• Description: Protection Device Intercept Error 1 (1K sheet finisher) Fuse blowout is detected
• Causes: • Over current (board defective, harness short-circuit, solenoid defective) (*721-03 only) • Motor defective (*excluding 721-03) • Connector disconnected (*excluding 721-03) • Overload (*excluding 721-03) • Encoder error (*720-10, 11, 17, 25, 44 only) • Home position sensor error (*Excluding 721-03, 10, 11, 17, 70, and 80) • Retreat sensor error (*721-42 only) • Needle jam (*721-44 only) • Home position sensor (folding blade HP) error (*721-52 only) • Home position sensor (folding cam HP) error (*721-52 only) • Paper surface sensor error (*721-70 only)
• Remedy: • Replace the controller • Replace the harness • Replace the motor (*excluding SC721-03) • Reset the connector (*excluding SC721-03) • Replace the solenoid (*SC721-03 only) • Replace the home position sensor (*excluding SC721-03, 10, 11, 17, 80)

• Code: SC721-10
• Description: Transport Motor 1 Error (1K sheet finisher) Motor driver detects an error state (DC motor control error) (1st time is jam notification, 2nd time is SC notification).
• Causes: • Over current (board defective, harness short-circuit, solenoid defective) (*721-03 only) • Motor defective (*excluding 721-03) • Connector disconnected (*excluding 721-03) • Overload (*excluding 721-03) • Encoder error (*720-10, 11, 17, 25, 44 only) • Home position sensor error (*Excluding 721-03, 10, 11, 17, 70, and 80) • Retreat sensor error (*721-42 only) • Needle jam (*721-44 only) • Home position sensor (folding blade HP) error (*721-52 only) • Home position sensor (folding cam HP) error (*721-52 only) • Paper surface sensor error (*721-70 only)
• Remedy: • Replace the controller • Replace the harness • Replace the motor (*excluding SC721-03) • Reset the connector (*excluding SC721-03) • Replace the solenoid (*SC721-03 only) • Replace the home position sensor (*excluding SC721-03, 10, 11, 17, 80)

• Code: SC721-11
• Description: Transport Motor 2 Error (1K sheet finisher) Motor driver detects an error state (DC motor control error) (1st time is jam notification, 2nd time is SC notification).
• Causes: • Over current (board defective, harness short-circuit, solenoid defective) (*721-03 only) • Motor defective (*excluding 721-03) • Connector disconnected (*excluding 721-03) • Overload (*excluding 721-03) • Encoder error (*720-10, 11, 17, 25, 44 only) • Home position sensor error (*Excluding 721-03, 10, 11, 17, 70, and 80) • Retreat sensor error (*721-42 only) • Needle jam (*721-44 only) • Home position sensor (folding blade HP) error (*721-52 only) • Home position sensor (folding cam HP) error (*721-52 only) • Paper surface sensor error (*721-70 only)
• Remedy: • Replace the controller • Replace the harness • Replace the motor (*excluding SC721-03) • Reset the connector (*excluding SC721-03) • Replace the solenoid (*SC721-03 only) • Replace the home position sensor (*excluding SC721-03, 10, 11, 17, 80)

• Code: SC721-17
• Description: Paper Eject Motor 2 Error (1K sheet finisher) Motor driver detects an error state (DC motor control error) (1st time is jam notification, 2nd time is SC notification).
• Causes: • Over current (board defective, harness short-circuit, solenoid defective) (*721-03 only) • Motor defective (*excluding 721-03) • Connector disconnected (*excluding 721-03) • Overload (*excluding 721-03) • Encoder error (*720-10, 11, 17, 25, 44 only) • Home position sensor error (*Excluding 721-03, 10, 11, 17, 70, and 80) • Retreat sensor error (*721-42 only) • Needle jam (*721-44 only) • Home position sensor (folding blade HP) error (*721-52 only) • Home position sensor (folding cam HP) error (*721-52 only) • Paper surface sensor error (*721-70 only)
• Remedy: • Replace the controller • Replace the harness • Replace the motor (*excluding SC721-03) • Reset the connector (*excluding SC721-03) • Replace the solenoid (*SC721-03 only) • Replace the home position sensor (*excluding SC721-03, 10, 11, 17, 80)