Thương hiệu phân phối chính hãng
Giỏ hàng

Mã lỗi Ricoh Aficio Pro C900 — Trang 72/85

Code: 797-18

Description: Book Door Lock Solenoid (SOL5) Error PB (D391) The book stack door is locked but the book door sensor (S98) did not go OFF.
Causes: • Book door sensor (S98) defective • Book door lock solenoid (SOL5) defective • Solenoid or sensor harness loose, broken, defective
Remedy:

Code: 797-19

Description: Glue Heater (HTR1) Error PB (D391) The heater failed to start because: 600 sec. after the bookbinder left the energy save mode, the glue thermistor did not detect the target temperature (153°C±5). -or- After the glue thermistor detected a glue temperature of 50°C, it did not detect a temperature above 140°C within 200 sec.
Causes: • Heater (HTR1) defective • Glue thermistor (S56) defective
Remedy:

Code: 797-2

Description: Grip End Sensor (S94) Error PB (D391)
Causes: The grip end sensor (S94) did not go OFF after the grip unit released the signature and moved the prescribed distance. • Book grip motor (M43) defective • Grip end sensor (S94) defective • Sensor or motor harness loose, broken, defective The grip end sensor (S94) did not go ON because the grip unit did arrive at the sensor position. • Book grip motor (M43) defective • Grip end sensor (S94) defective • Sensor or motor harness loose, broken, defective • Data received for signature data was incorrect.
Remedy:

Code: 797-20

Description: Electrical Short in the Gluing Unit PB (D391) A short circuit or wire breakage occurred in the gluing unit. The glue thermistor (S56) detected: • A temperature over 200°C more than 1 sec. (short circuit) • A temperature of less than 5°C for more than 1 sec. or more than 10 sec. after power on (wire breakage) • The AD value of the glue level thermistor (S58) remained at 1023 for 10 sec (wire breakage).
Causes: • Heater (HTR1) defective • Glue thermistor (S56) defective
Remedy:

Code: 797-21

Description: Temperature Detection Error PB (D391)
Causes: After adjustment of the glue temperature, the glue temperature thermistor (S56) detected a temperature lower than 135C for more than 10 sec. • Heater (HTR1) defective • Glue thermistor (S56) defective The glue level thermistor detected a temperature higher than 170°C for longer than 10 sec. after the glue had warmed up. -or- The glue level thermistor detected a temperature higher than 100°C for longer than 10 sec. after the glue had warmed up. • Glue level thermistor (S58) defective
Remedy:

Code: 797-22

Description: Protection Circuit Error PB (D391) The thermostat (THSW1) inside the gluing unit detected an abnormally high temperature.
Causes: • Glue heater (HTR1)defective • Thermostat (THSW1) defective
Remedy:

Code: 797-23

Description: Glue Surface Error 1 PB (D391)
Causes: The surface of the glue in the vat did not reach the lower limit position. This error occurred when the glue surface was detected below the lower limit position 4 times in succession during the glue replenishment cycle. • Glue has clogged in the vat • Glue supply defective • Glue level thermistor (S58) defective The glue level thermistor could not detect the glue surface at the upper limit position: 1) After glue was detected above the low limit mark, and 2) After 12 glue packets were supplied, and 3) No glue had been recently applied. • Glue has clogged in the vat • Glue level thermistor (S58) defective
Remedy:

Code: 797-24

Description: Glue Surface Error 2 PB (D391) Without a glue vat refill, the glue level thermistor could not detect the level of the glue below the upper limit (full) level, even after the application of 25.42 g of glue.
Causes: • Glue application abnormal (not applying correctly) • Glue level thermistor (S58) defective
Remedy:
Đăng ký nhận bản tin Đăng ký nhận bản tin Đăng ký nhận bản tin Đăng ký nhận bản tin
Đăng ký nhận bản tin
Nhận ưu đãi sớm nhất khi chương trình diễn ra

Đăng ký nhận bản tin

Việc cho phép sử dụng cookie sẽ giúp cải thiện trải nghiệm của bạn trên trang web này. Chính sách cookie