Thương hiệu phân phối chính hãng
Giỏ hàng

Mã lỗi Ricoh Aficio SPC420DN — Trang 10/15

Code: 687

Description: Controller board command error
A command from the controller board is not received.
Causes: Loose connection. Defective controller board. Defective EGB.
Remedy: 1. Check the connection of the controller board. 2. Replace the controller board. 3. Replace the EGB.

Code: 690

Description: EGB data error
The data transfer in the EGB is interrupted by some incident (e.g. cover open etc.) during the data transfer.
Causes: Defective EGB
Remedy: 1. Replace the EGB.

Code: 818

Description: Watchdog error
While the system program is running, no other programs can run (due to a bus hold or endless loop).
Causes: Defective system program. Defective controller board.
Remedy: 1. Reinstall the system program. 2. Replace the controller board.

Code: 819

Description: Kernel stop
Causes: [0696e] [B] System completely down • Defective RAM DIMM • Defective controller • Software error 1. Check and/or replace the RAM DIMM. 2. Replace the controller. VM full error [0766d] [B] Unexpected system memory size • Defective RAM DIMM • Defective controller • Software error 1. Check and/or replace the RAM DIMM. 2. Replace the controller. Cache error [4361] [B] Cache error in the CPU • Defective CPU 1. Replace the controller board. The others [----] [B] Error in OS • Defective memory • Defective flash memory • Defective CPU 1. Replace the controller board.
Remedy:

Code: 820

Description: Self-Diagnostic Error: CPU
Causes: • Defective CPU device
Remedy:

Code: 821

Description: Self-Diagnostic Error: ASIC
Causes: [0B00] [B] The write-&-verify check error has occurred in the ASIC. • Defective controller board 1. Replace the controller. ASIC not detected [0B06] [B] The ASIC of the I/O is not detected. • ASIC (controller board defective) • Poor connection between North Bridge and PCI I/F. 1. Replace controller board. SHM register check error [0B10] [B] Failed to initialize or could not read connection bus. Data in SHM register incorrect. • Defective bus connection • Defective SHM 1. Replace controller board Timer error between ASIC and CPU [0D05] [B] The CPU checks if the ASIC timer works properly compared with the CPU timer. • System firmware problem • Defective RAM-DIMM • Defective controller If the ASIC timer does not function in the specified range, this SC code is displayed. • Reinstall the controller system firmware. 1. Replace the RAM-DIMM. 2. Replace the controller board.
Remedy:

Code: 822

Description: Self-Diagnostic Error: HDD. Timeout error/ [3004]: Command error [3003] [B] When the main switch is turned on or starting the self-diagnostic, the HDD stays busy for the specified time or more.
Causes: • Loose connection • Defective HDD • Defective controller
Remedy: 1. Check that the HDD is correctly connected to the controller. 2. Replace the HDD. 3. Replace the controller.

Code: 823

Description: Self-diagnostic Error: NIB
Causes: MAC address check sum error [6101] [B] The result of the MAC address check sum does not match the check sum stored in ROM. • Defective controller 1. Replace the controller. PHY IC error [6104] [B] The PHY IC on the controller cannot be correctly recognized. Same as SC823-[6101] PHY IC loop-back error [6105] [B] An error occurred during the loop-back test for the PHY IC on the controller.
Remedy:
Đăng ký nhận bản tin Đăng ký nhận bản tin Đăng ký nhận bản tin Đăng ký nhận bản tin
Đăng ký nhận bản tin
Nhận ưu đãi sớm nhất khi chương trình diễn ra

Đăng ký nhận bản tin

Việc cho phép sử dụng cookie sẽ giúp cải thiện trải nghiệm của bạn trên trang web này. Chính sách cookie