Thương hiệu phân phối chính hãng
Giỏ hàng

Mã lỗi Ricoh Aficio SPC440DN — Trang 10/16

Code: 545

Description: Heating roller fusing lamp consecutive full power 1 When the fusing unit is not running in the ready condition, the heating roller fusing lamp keeps on full power for 30 seconds.
Causes: • Broken heating roller thermostat • Broken heating roller fusing lamp
Remedy: 1. Replace the heating roller thermostat. 2. Replace the heating roller fusing lamp.

Code: 547-01

Description: Zero cross error (Fusing relay short) • The zero cross signal is detected three times even though the heater relay is off when turning on the main power. • The zero cross signal is not detected for 3 seconds even though the heater relay is on after turning on the main power or closing the front door. • The detection error occurs twice or more in the 11 zero cross signal detections. This error is defined when the detected zero cross signal is less than 45.
Causes: • Defective fusing lamp relay • Defective fusing lamp relay circuit
Remedy: 1. Replace the PSU. 2. Replace the BCU.

Code: 547-02

Description: Zero cross error (Fusing relay open) • The zero cross signal is detected three times even though the heater relay is off when turning on the main power. • The zero cross signal is not detected for 2 seconds even though the heater relay is on after turning on the main power or closing the front door. • The detection error occurs twice or more in the 11 zero cross signal detections. This error is defined when the detected zero cross signal is less than 45.
Causes: • Defective fusing lamp relay • Defective fusing lamp relay circuit • Short 24VS fuse
Remedy: 1. Replace the 24VS fuse (FU3/FU4). 2. Replace the PSU. 3. Replace the BCU.

Code: 547-03

Description: Zero cross error • The zero cross signal is detected three times even though the heater relay is off when turning on the main power. • The zero cross signal is not detected for 2 seconds even though the heater relay is on after turning on the main power or closing the front door. • The detection error occurs twice or more in the 11 zero cross signal detections
Causes: • Unstable power supply
Remedy: • Check the power supply source.

Code: 551

Description: Heating roller thermistor (end) error 2 The temperature measured by the heating roller thermistor (end) does not reach 0°C for 6 seconds.
Causes: • Loose connection of heating roller thermistor (end) • Defective heating roller thermistor (end)
Remedy: 1. Check that the heating roller thermistor (end) is firmly connected. 2. Replace the heating roller thermistor (end).

Code: 552

Description: Heating roller warm-up error 2 The heating roller temperature does not reach the ready temperature while 70 seconds after the heating lamp on.
Causes: • Dirty or defective thermistor (end) • Heating roller fusing lamp broken • Defected thermostat • Defective heating roller fusing lamp
Remedy: 1. Check if the heating roller thermistor (end) is firmly connected. 2. Replace the heating roller thermistor (end). 3. Replace the heating roller fusing lamp.

Code: 553

Description: Heating roller fusing lamp overheat 2 (software error) The detected pressure roller temperature stays at 230°C or more for 1 second.
Causes: • Defective PSU • Defective BCU
Remedy: 1. Replace the heating roller thermistor (end). 2. Replace the PSU. 3. Replace the BCU.

Code: 554

Description: Heating roller fusing lamp overheat 2 (hardware error) The heating roller thermistor (end) detects 250°C or more.
Causes: • Defective heating roller thermistor (end) • Defective PSU • Defective BCU • Defective fusing control system
Remedy: 1. Replace the heating roller thermistor (end). 2. Replace the PSU. 3. Replace the BCU.
Đăng ký nhận bản tin Đăng ký nhận bản tin Đăng ký nhận bản tin Đăng ký nhận bản tin
Đăng ký nhận bản tin
Nhận ưu đãi sớm nhất khi chương trình diễn ra

Đăng ký nhận bản tin

Việc cho phép sử dụng cookie sẽ giúp cải thiện trải nghiệm của bạn trên trang web này. Chính sách cookie