Thương hiệu phân phối chính hãng
Giỏ hàng

Mã lỗi Ricoh B237 MPC3000 AT-C1b — Trang 10/24

Code: 503-01

Description: Tray 3 error (Paper Feed Unit or LCT)
For the paper feed unit: When the tray lift motor is turned on, the upper limit is not detected within 10 seconds For the LCT: SC 503-01 occurs if the upper or lower limit is not detected within 8 seconds when the tray lift motor is turned on to lift or lower the tray.
Causes: For the paper feed unit: Defective tray lift motor or connector disconnection Defective lift sensor or connector disconnection For the LCT: Defective stack transport clutch or connector disconnection Defective tray motor or connector disconnection Defective end fence home position sensor or connector disconnection Defective upper limit sensor or connector disconnection Defective tray lift motor or connector disconnection
Remedy: 1. Check the cable connections. 2. Check and/or replace the defective component.

Code: 503-02

Description: Tray 3 error (Paper Feed Unit or LCT)
This SC is generated if the following condition occurs 3 consecutive times. For the paper feed unit: When the tray lowers, the tray lift sensor does not go off within 1.5 sec. For the LCT: When the main switch is turned on or when the LCT is set, if the end fence is not in the home position (home position sensor ON), the tray lift motor stops. If the upper limit does not go off for 1.5 seconds even the tray lift motor turns on to lower the tray after the upper limit has been detected at power on.
Causes: For the paper feed unit: Defective tray lift motor or connector disconnection. Defective lift sensor or connector disconnection For the LCT: Defective stack transport clutch or connector disconnection. Defective tray motor or connector disconnection. Defective end fence home position sensor or connector disconnection
Remedy: 1. Check the cable connections. 2. Check and/or replace the defective component.

Code: 504-01

Description: Tray 4 error (Paper Feed Unit or LCT)
For the two-tray paper feed unit When the tray lift motor is turned on, the upper limit is not detected within 10 seconds. If this condition occurs three consecutive times, the SC is generated. For the LCT If the upper or lower limit is not detected within 8 seconds when the tray lift motor is turned on to lift up or lower the tray
Causes: Defective tray lift motor or connector disconnection. Defective lift sensor or connector disconnection
Remedy: 1. Check the cable connections. 2. Check and/or replace the defective component.

Code: 504-02

Description: Tray 4 error (3 Tray Paper Feed Unit)
This SC is generated if the following condition occurs 3 consecutive times. For the two-tray paper feed unit. When the tray lowers, the tray lift sensor does not go off within 1.5 sec. For the LCT. If the upper limit does not go off for 1.5 seconds even the tray lift motor turns on to lower the tray after the upper limit has been detected at power on.
Causes: Defective tray lift motor or connector disconnection. Defective lift sensor or connector disconnection
Remedy: 1. Check the cable connections. 2. Check and/or replace the defective component.

Code: 530

Description: Fusing/Paper exit fan error
The BICU does not receive the lock signal 10 seconds after turning on the fusing/paper exit fan.
Causes: Defective fusing/paper exit fan motor or connector disconnection. Defective BICU
Remedy: 1. Check the connector and/or replace the fusing/paper exit fan motor.

Code: 531

Description: Drive unit fan error
The BICU does not receive the lock signal 10 seconds after turning on the drive unit fan motor.
Causes: Defective drive unit fan motor
Remedy: 1. Replace the drive unit fan motor.

Code: 532

Description: Ventilation fan (at the left side of the machine) motor-front/rear error
The BICU does not receive the lock signal 10 seconds after turning on the ventilation fan motor-front/rear.
Causes: Defective ventilation fan motor-front or rear
Remedy: 1. Replace the ventilation fan (at the left side of the machine) motor-front or rear.

Code: 533

Description: Toner supply tube fan error
The BICU does not receive the lock signal 10 seconds after turning on the toner supply tube fan motor.
Causes: Defective toner supply tube fan motor-front or rear
Remedy: 1. Replace the toner supply tube fan motor.
Đăng ký nhận bản tin Đăng ký nhận bản tin Đăng ký nhận bản tin Đăng ký nhận bản tin
Đăng ký nhận bản tin
Nhận ưu đãi sớm nhất khi chương trình diễn ra

Đăng ký nhận bản tin

Việc cho phép sử dụng cookie sẽ giúp cải thiện trải nghiệm của bạn trên trang web này. Chính sách cookie