Description: Tray 1 lift malfunction • The lift sensor is not activated within 10 s after the tray lift motor starts lifting the bottom plate. • When the tray lowers, the tray lift sensor does not go off within 1.5 s. • Tray overload detected when the tray is set. • The lower limit sensor of the LCT does not detect the lower limit within 10 s.
Causes: • Tray lift motor defective, disconnected • Paper or other obstacle trapped between tray and motor • Pick-up solenoid disconnected, blocked by an obstacle • Too much paper loaded in tray Note • At first, the machine displays a message asking the operator to reset the tray. • This SC will not display until the operator has pulled the tray out and pushed it in 3 times. • If the operator turns the machine off/on before the 3rd opening and closing of the tray, the 3-count is reset.
Description: Tray 2 lift malfunction • The lift sensor is not activated within 10 s after the tray lift motor starts lifting the bottom plate. • When the tray lowers, the tray lift sensor does not go off within 1.5 s. • Tray overload detected when the tray is set.
Causes: • Tray lift motor defective or disconnected • Paper or other obstacle trapped between tray and motor • Pick-up solenoid disconnected or blocked by an obstacle • Too much paper loaded in tray Note • At first, the machine displays a message asking the operator to reset the tray. • This SC will not display until the operator has pulled the tray out and pushed it in 3 times. • If the operator turns the machine off/on before the 3rd opening and closing of the tray, the 3-count is reset.
Description: Tray 3 lift malfunction • The lift sensor is not activated within 10 s after the tray lift motor starts lifting the bottom plate. • When the tray lowers, the tray lift sensor does not go off within 1.5 s. • Tray overload detected when the tray is set.
Causes: • Tray lift motor defective or disconnected • Paper or other obstacle trapped between tray and motor • Pick-up solenoid disconnected or blocked by an obstacle • Too much paper loaded in tray Note • At first, the machine displays a message asking the operator to reset the tray. • This SC will not display until the operator has pulled the tray out and pushed it in 3 times. • If the operator turns the machine off/on before the 3rd opening and closing of the tray, the 3-count is reset.
Description: Tray 4 lift malfunction • The lift sensor is not activated within 10 s after the tray lift motor starts lifting the bottom plate. • When the tray lowers, the tray lift sensor does not go off within 1.5 s. • Tray overload detected when the tray is set.
Causes: • Tray lift motor defective or disconnected • Paper or other obstacle trapped between tray and motor • Pick-up solenoid disconnected or blocked by an obstacle • Too much paper loaded in tray Note • At first, the machine displays a message asking the operator to reset the tray. • This SC will not display until the operator has pulled the tray out and pushed it in 3 times. • If the operator turns the machine off/on before the 3rd opening and closing of the tray, the 3-count is reset.
Description: LCT feed motor malfunction One of the following conditions is detected: • The LD signal from the feed motor is detected abnormal for 50 ms after the motor switches on. • At power on, the motor is detected loose or disconnected.
Causes: • Feed motor defective • Feed motor connector disconnected • Obstacle interfering with mechanical movement of motor
Remedy:
Nhận ưu đãi sớm nhất khi chương trình diễn ra
Đăng ký nhận bản tin
Việc cho phép sử dụng cookie sẽ giúp cải thiện trải nghiệm của bạn trên trang web này.
Chính sách cookie
Những cookie này là cần thiết để trang web hoạt động đúng cách.
Những cookie này giúp chúng tôi hiểu cách khách truy cập tương tác với trang web.
Những cookie này được sử dụng để cung cấp quảng cáo cá nhân hóa.