Thương hiệu phân phối chính hãng
Giỏ hàng

Mã lỗi Ricoh D136 MPC8002SP CH-C1 — Trang 35/63

Code: SC560-00

Description: Web unit contact error Contact/separation control failed 3 times consecutively. Monitored when contact/separation mechanism is operating.
Causes: • Web unit contact motor/sensor defective • Feeler deformed or damaged • Contact/separation mechanism defective
Remedy: • Replace the motor. • Replace the sensor. • Replace the feeler. • Replace the unit.

Code: SC561-00

Description: Sensor 2: Heating Roller Front Disconnection 0 degrees or lower was detected for (t1) seconds consecutively. Number of times: 10 or more D135 (Japan): 50 (seconds) D136 (Japan)/D135 (NA): 50 (seconds) D136 (NA)/D135 (EU)/D136(EU): 50 (seconds) D137 (Japan): 50 (seconds) D138 (Japan)/D137 (NA)/D138 (NA)/D137 (EU)/D138 (EU): 50 (seconds) Monitored at: All times, though SC is not issued when temperature is not controlled (when in off mode/sleep mode, when a door, excluding the toner supply door, is open, or when the heater relay is off).
Causes: • Thermistor disconnection • Connecter contact failure
Remedy: • Replace the thermistor. • Reconnect the connector. • Replace the connector. • Replace the connector.

Code: SC562-02

Description: Sensor 2: Heating Roller Front: Reload Failure: Timeout 1 Failed to reach (T2) degrees centigrade after (t4) seconds from the start of heater control. D135 (Japan):T2 = 45, t4 = 80 D136 (Japan)/D135 (NA): T2 = 45, t4 = 80 D136 (NA)/D135 (EU)/D136(EU): T2 = 45, t4 = 80 D137 (Japan): T2 = 45, t4 = 80 D138 (Japan)/D137 (NA)/D138 (NA)/D137 (EU)/D138 (EU): T2 = 45, t4 = 80 Monitored at: Startup (Power-on, when a cover is closed, when fuser heater is under control)
Causes: • Thermopile lens smudged • Thermistor deformed or floating • Input voltage out of specification
Remedy: • Replace the thermopile. • Use with supported input voltage • Replace the IH coil/IH inverter. • Replace the unit.

Code: SC562-03

Description: Sensor 2: Heating Roller Front: Reload Failure: Timeout 2 Failed to reach reload temperature after (t5) seconds from the start of heater control. D135 (Japan):t5 = 350 D136 (Japan)/D135 (NA): t5 = 350 D136 (NA)/D135 (EU)/D136(EU): t5 = 350 D137 (Japan): t5 = 350 D138 (Japan)/D137 (NA)/D138 (NA)/D137 (EU)/D138 (EU): t5 = 350 Monitored at: Startup (Power-on, when a cover is closed, when fuser heater is under control)
Causes: • IH malfunctioning • Overheating prevention device worked.
Remedy: • Replace the thermopile. • Use with supported input voltage • Replace the IH coil/IH inverter. • Replace the unit.

Code: SC563-00

Description: Sensor 2: Heating Roller Front: Overheat detection (software) (T3) degrees centigrade or higher was detected for (t6) seconds consecutively. Number of times: 10 or more D135 (Japan):T3 = 250, t5 = 1 D136 (Japan)/D135 (NA): T3 = 250, t5 = 1 D136 (NA)/D135 (EU)/D136(EU): T3 = 250, t5 = 1 D137 (Japan): T3 = 250, t5 = 1 D138 (Japan)/D137 (NA)/D138 (NA)/D137 (EU)/D138 (EU): T3 = 250, t5 = 1 Monitored at: All times, though SC is not issued when temperature is not controlled (when in off mode/sleep mode, when a door, excluding the toner supply door, is open, or when the heater relay is off).
Causes: • Triac shorted. • IOB board defective.
Remedy: • Replace the IOB board. • Replace the unit.

Code: SC564-00

Description: Heating Roller Front: Overheat detection (hardware) Hardware detection of overheat condition. The heating roller front thermistor was detected as the cause.
Causes: • IOB defective • Fuser control software running out of control • Heating roller front thermistor defective • IH inverter supplied continuously (software error or temperature sensor malfunctioning
Remedy: • After removing the cause of the SC, Set "Fusing SC Clear" in the SP mode. • If necessary, replace: IOB/heating roller front thermistor/IH coil/IH inverter.

Code: SC569-02

Description: Pressure Release Error: HP failed 3 times Pressure release/Home position/control failed 3 times consecutively. Monitored when the pressure release mechanism is operating. Pressure Change: SP1-151-001 1:On/0: Off When this SP is set to OFF, SC detection is disabled.
Causes: • Pressure release motor, sensor defective • Feeler deformed or damaged • Pressure release mechanism defective
Remedy: • Replace the motor. • Replace the sensor. • Replace the feeler. • Replace the unit.

Code: SC569-03

Description: Pressure Release Error: Overrun When sensor A shows Low and Sensor B shows High. Except when home position is detected. Monitored when the pressure release mechanism is operating. Pressure Change: SP1-151-001 1:On/0: Off When this SP is set to OFF, SC detection is disabled.
Causes: • Pressure release motor, sensor defective • Feeler deformed or damaged • Pressure release mechanism defective
Remedy: • Replace the motor. • Replace the sensor. • Replace the feeler. • Replace the unit.
Đăng ký nhận bản tin Đăng ký nhận bản tin Đăng ký nhận bản tin Đăng ký nhận bản tin
Đăng ký nhận bản tin
Nhận ưu đãi sớm nhất khi chương trình diễn ra

Đăng ký nhận bản tin

Việc cho phép sử dụng cookie sẽ giúp cải thiện trải nghiệm của bạn trên trang web này. Chính sách cookie