Thương hiệu phân phối chính hãng
Giỏ hàng

Mã lỗi Ricoh D250 MP3054 Cor-C1 — Trang 12/40

Code: SC551-03

Description: Edge NC Sensor Short-circuit AD value: 0-13 (FB voltage: 0.000V-0.041V) is detected for specified seconds continuously. Detection period: 100 ms, detection frequency: 10 times or more.
Causes: • NC sensor short-circuit • Connector disconnected
Remedy: • Replace the NC sensor. • Reset the connector. • Replace the connector. • Replace the fusing unit.

Code: SC552-02

Description: Fusing Edge Thermopile Does Not Reload When the fusing edge thermopile does not reach a predetermined temperature for specified seconds consecutively.
Causes: • Thermopile lens dirt • Thermopile modification, float • Outside input voltage guarantee • After excessive temperature rise prevention unit operation
Remedy: • Replace the thermopile. • Make sure that the input voltage is within acceptable limits. • Replace the fusing unit.

Code: SC552-03

Description: Fusing Edge Thermopile Does Not Reload Heating edge reload permission temperature not reached after heater 1 ON for specified seconds.
Causes: • Thermopile lens dirt • Thermopile modification, float • Outside input voltage guarantee • After excessive temperature rise prevention unit operation
Remedy: • Replace the thermopile. • Make sure that the input voltage is within acceptable limits. • Replace the fusing unit.

Code: SC552-05

Description: Fusing Edge Thermopile Does Not Reload (Low Voltage) When the fusing edge thermopile does not reach a predetermined temperature for specified seconds consecutively.
Causes: • Thermopile lens dirt • Thermopile modification, float • Outside input voltage guarantee • After excessive temperature rise prevention unit operation
Remedy: • Replace the thermopile. • Make sure that the input voltage is within acceptable limits. • Replace the fusing unit.

Code: SC552-06

Description: Fusing Edge Thermopile Does Not Reload (Low Voltage) When the fusing edge thermopile does not reach the permission temperature of heat edge reloading for specified seconds continuously.
Causes: • Thermopile lens dirt • Thermopile modification, float • Outside input voltage guarantee • After excessive temperature rise prevention unit operation
Remedy: • Replace the thermopile. • Make sure that the input voltage is within acceptable limits. • Replace the fusing unit.

Code: SC553-00

Description: Fusing End Thermopile High Temperature Detection (software) Above a predetermined temperature detected for specified seconds continuously. Detection period: 100ms, detection count: 10 times or more.
Causes: • Triac short-circuit • IOB defective • BCU defective
Remedy: • Replace the IOB. • Replace the BCU. • Replace the fusing unit.

Code: SC554-01

Description: Fusing End Thermopile High Temperature Detection (hardware) In the event of an error
Causes: • Triac defective (short-circuit) • Engine controller defective • Heating edge thermopile defective • Fusing control software: out of control
Remedy: • If the triac is defective, replace the AC power supply board. • If necessary, replace the BCU or heating edge thermopile.

Code: SC554-02

Description: Fusing End NC Sensor High Temperature Detection (hardware) In the event of an error
Causes: • Triac defective (short-circuit) • Engine controller defective • Heating edge thermopile defective • Fusing control software: out of control
Remedy: • Attach the new fusing unit, then run SP-5-810-002. • If necessary, replace the BCU or Fusing edge NC sensor.
Đăng ký nhận bản tin Đăng ký nhận bản tin Đăng ký nhận bản tin Đăng ký nhận bản tin
Đăng ký nhận bản tin
Nhận ưu đãi sớm nhất khi chương trình diễn ra

Đăng ký nhận bản tin

Việc cho phép sử dụng cookie sẽ giúp cải thiện trải nghiệm của bạn trên trang web này. Chính sách cookie