Thương hiệu phân phối chính hãng
Giỏ hàng

Mã lỗi Ricoh M125 SPC831DN — Trang 12/24

Code: 544

Description: Fusing sleeve belt overheat: Center (hardware error)
During stand-by mode or a print job, the detected fusing sleeve belt temperature reaches 250°C.
Causes: Defective PSU. Defective BCU. Defective AC control board. Defective IOB. Defective fusing control system.
Remedy: • Replace the PSU. • Replace the BCU. • Replace the AC controller board. • Replace the IOB. Replace the fusing unit and reset the counter of the fusing unit using SP3-902-014. Important: • The fusing unit cannot be used because an abnormal high temperature was detected. After this SC occurs, the counter reset of the fusing unit should be done manually using SP3-902-014 because the counter reset is not done automatically. • After replacing fusing unit, to set SP5-810-2 is necessary to reset this SC.

Code: 545

Description: Fusing Heater error: Center
The fusing heater keeps full power for 9 seconds or more.
Causes: Defective thermistors. Broken heater cables. This is determined after the device for preventing excessive temperature rise operates.
Remedy:

Code: 547

Description: Zero cross error
After the zero-crossing interrupt setting is enabled, the machine waits for 50+-20 ms. If a request for zero-crossing interrupt is received while waiting, the machine retries the search after the waiting time is completed. The detection occurs consecutively 3 times.
Causes: Defective fusing relay. Defective fusing relay circuit.
Remedy: • Turn the main power switch off and on. • If the fusing relay is damaged, replace the PSU. • Check the connection between the PSU and control board, and then replace the harness and board if necessary.

Code: 549

Description: Fusing heater connection error
The fusing sleeve belt rotation sensor detects the target temperature as 50°C for 5 seconds or more after the fusing/paper exit motor has turned on.
Causes: Broken heater cables. Loose connection.
Remedy:

Code: 551

Description: Fusing sleeve belt thermistor error
The temperature at the end of the fusing sleeve belt measured by the fusing sleeve belt thermistor does not reach -50°C for 0.1 seconds.
Causes: Defective thermopile. Defective thermistor. Loose connection.
Remedy:

Code: 552

Description: Fusing sleeve belt warm-up error 2
The fusing sleeve belt temperature does not reach 81C for 6 seconds after the inverter turned on.)
Causes: Dirty thermopile lenses. Deformed thermistor.
Remedy:

Code: 553

Description: Fusing sleeve belt overheat: End (software error)
The detected fusing sleeve belt temperature stays at 240°C or more for 1 second for 10 consecutive times.
Causes: The triac switch has shorted out. Defective IOB. Defective BCU.
Remedy:

Code: 554

Description: Fusing sleeve belt overheat: End (hardware error)
The fusing sleeve belt thermistor detects 250°C or more.
Causes: Defective PSU. Defective BCU. Defective AC control board. Defective IOB. Defective fusing control system.
Remedy: • Replace the PSU. • Replace the BCU. • Replace the AC controller board. • Replace the IOB. • Replace the fusing unit and reset the counter of the fusing unit using SP3-902-014. Important: The fusing unit cannot be used because an abnormal high temperature was detected. • After this SC occurs, the counter reset of the fusing unit should be done manually using SP3-902-014 because the counter reset is not done automatically. • After replacing fusing unit, to set SP5-810-2 is necessary to reset this SC.
Đăng ký nhận bản tin Đăng ký nhận bản tin Đăng ký nhận bản tin Đăng ký nhận bản tin
Đăng ký nhận bản tin
Nhận ưu đãi sớm nhất khi chương trình diễn ra

Đăng ký nhận bản tin

Việc cho phép sử dụng cookie sẽ giúp cải thiện trải nghiệm của bạn trên trang web này. Chính sách cookie