Thương hiệu phân phối chính hãng
Giỏ hàng

Mã lỗi Sharp AR275 — Trang 7/10

Code: F9 84

Description: Communication trouble between MCU and printer PWB (Framing error)
Causes: Printer PWB connector disconnection Harness trouble between the printer PWB and the MCU PWB Motherboard connector pin breakage Printer PWB ROM trouble/Data disturbance
Remedy: Check the connectors and harness of the printer PWB and MCU PWB. Check the grounding of the copier. Check ROM on printer PWB.

Code: F9 88

Description: Communication trouble between MCU and printer PWB (Timeout error)
Causes: Printer PWB connector disconnection Harness trouble between the printer PWB and the MCU PWB Motherboard connector pin breakage Printer PWB ROM trouble/Data disturbance
Remedy: Check the connectors and harness of the printer PWB and MCU PWB. Check the grounding of the copier. Check ROM on printer PWB.

Code: F9 99

Description: The machine language setup does not coincide with the PCL board language setup.
Causes: PCL board connection error SIM setup error
Remedy: Check the firmware of the PCL board and the combination of the panel screen data, and download the correct version, if necessary. Check the machine language information. (Machine language setup: SIM 26-22)

Code: H2 00

Description: Thermistor open detection Fusing unit not installed
Causes: Thermistor defect Control PWB failure Fusing section connector contact failure Fusing unit not installed
Remedy: Check the harness and the connector of the thermistor and the MCU. Clear the display of self-diagnostics with SIM 14. Remarks Thermistor open

Code: H3 00

Description: Heat roller abnormally high temperature. The fusing temperature is over 220°C.
Causes: Thermistor defect Control PWB failure Fusing section connector contact failure
Remedy: Check the heater lamp blinking with SIM 5- 2. When the lamp blinks normally: Check the thermistor and the harness. Check the MCU PWB thermistor input circuit. If lamp lights and stays lit: Check the power PWB and the MCU PWB lamp control circuit. Clear the display of self-diagnostics with SIM 14.

Code: H4 00

Description: Heat roller abnormally low temperature. The setup temperature (about 90°C is not reached within the specified time (about 35sec) from turning on the power ON SW. (When the temperature falls below 120°C in the standby mode.)
Causes: Thermistor defect Heater lamp failure Thermostat failure Control PWB failure
Remedy: Check the heater lamp blinking with SIM 5- 2. When the lamp blinks normally: Check the thermistor and the harness. Check the MCU PWB thermistor input circuit. When the lamp does not light: Check for disconnection of the heater lamp and thermostat. Check the interlock switch. Check the power PWB and the MCU PWB lamp control circuit. Clear the display of self-diagnostics with SIM 14.

Code: H5 01

Description: 5 continuous T10D(T20D) not-reaching JAM. T10D(T20D) not-reaching JAM was detected 5 continuous times.
Causes: The fusing JAM is not completely removed. (Jam paper remains.) T10D or T20D sensor breakdown or harness connection trouble Fusing unit installation failure
Remedy: Check for jam paper in the fusing section. (paper winding, etc.) Check fusing unit installation Clear the trouble with SIM 14.

Code: H5 02

Description: Fusing thermistor abnormality detect. Fusing thermistor temperature transient abnormality (Paper winding)
Causes: Paper wound around the fusing roller. Fusing pawl abnormality Fusing unit installation failure
Remedy: Check for jam paper in the fusing section. (paper winding, etc.) Check installation of the fusing unit. Check the fusing pawl. Clear the trouble with SIM 14.
Đăng ký nhận bản tin Đăng ký nhận bản tin Đăng ký nhận bản tin Đăng ký nhận bản tin
Đăng ký nhận bản tin
Nhận ưu đãi sớm nhất khi chương trình diễn ra

Đăng ký nhận bản tin

Việc cho phép sử dụng cookie sẽ giúp cải thiện trải nghiệm của bạn trên trang web này. Chính sách cookie