Thương hiệu phân phối chính hãng
Giỏ hàng

Mã lỗi Sharp AR285 — Trang 6/11

Code: F9 04

Description: Printer program error. Program data trouble in the option printer board.
Causes: Flash memory data is destroied.
Remedy: Replace or rewrite the Flash memory. Replace the printer PWB.

Code: F9 10

Description: PRT SCSI LSI abnormality. An error occurred in SCSI communication with the option printer board.
Causes: SCSI LSI abnormality ISU PWB abnormality SCSI connector improper connection
Remedy: Replace the printer PWB. Check the SCSI connector. Replace the ISU PWB.

Code: F9 90

Description: Printer communication trouble (PRT detection). Communication setup error/framing/parity/protocol error
Causes: Slave unit PWB connector improper connection Slave unit PWB – ICU PWB harness trouble Slave unit PWB mother board connector pin breakage
Remedy: Check the slave unit PWB and the ICU PWB connector connection. Check the copier earth.

Code: FC 00

Description: ASK/IrDA modulation LSI reset error. Though the RESET signal pulse is sent to the ASK/IrDA modulation LSI, the power signal is not turned ON.
Causes: 1) ICU main PWB defect 2) ASK/IrDA modulation LSI/Clock oscillator defect
Remedy: Perform the self diag with SIM 68-01. Replace the ICU main PWB.

Code: FC 01

Description: ASK/IrDA switch error. Though the ASK/IrDA switch command is sent to the ASK/IrDA modulation LSI, the AI signal is not changed.
Causes: 1) ICU main PWB defect 2) ASK/IrDA modulation LSI/Clock oscillator defect
Remedy: Perform the self diag with SIM 68-01. Replace the ICU main PWB.

Code: H2 00, H2 HL1

Description: Thermister open Fusing unit not installed. Thermister is open (more than 4.6-V input voltage is detected). Fusing unit not installed
Causes: Thermister defective Control PWB defective Improper connection of fusing connector AC power supply defective Fusing unit not installed
Remedy: Check harness and connector between thermister and control PWB. Clear the display of self-diagnostics with SIM14.

Code: H2 01, H2 HL2

Description: Thermister open Fusing unit not installed. Thermister is open (more than 4.6-V input voltage is detected). Fusing unit not installed
Causes: Thermister defective Control PWB defective Improper connection of fusing connector AC power supply defective Fusing unit not installed
Remedy: Check harness and connector between thermister and control PWB. Clear the display of self-diagnostics with SIM14.

Code: H3 00, H3 HL1

Description: Heat roller high temperature detection. The fusing temperature is over 241.5°C (less than 1.3-V input voltage is detected.)
Causes: Thermister defective Control PWB defective Improper connection of fusing unit connector AC power supply defective
Remedy: Check heater lamp operation with SIM5-2. If lamp blinks properly: Check thermister and its harness. Check thermister input circuit of control PWB. If lamp lights and stays lit: Check lamp control circuits of AC PWB and control PWB. Clear the trouble with SIM14.
Đăng ký nhận bản tin Đăng ký nhận bản tin Đăng ký nhận bản tin Đăng ký nhận bản tin
Đăng ký nhận bản tin
Nhận ưu đãi sớm nhất khi chương trình diễn ra

Đăng ký nhận bản tin

Việc cho phép sử dụng cookie sẽ giúp cải thiện trải nghiệm của bạn trên trang web này. Chính sách cookie