Thương hiệu phân phối chính hãng
Giỏ hàng

Mã lỗi Sharp MXM700U — Trang 11/16

Code: F6-97

Description: FAX-BOX incompatibility trouble
The FAX-BOX PWB is not one for the main unit. (FAX detection) If the FAX-BOX modem controller PWB information (hard detection) is not for the main unit, it is judged as an error.
Causes: Because the FAX-BOX modem controller PWB information (hard detection) is not for the main unit.
Remedy: Check the FAX-BOX modem controller PWB. Replace it with a modem controller PWB for the main unit.

Code: F6-98

Description: Combination error of the FAX-BOX destination information and the machine destination information
When the destination information stored in the FAX-BOX EEPROM is compared with that of the machine, and if the combination is improper, it is judged as an error.
Causes: Because of improper combination between the destination information stored in the EEPROM on the FAX-BOX PWB and that of the machine (set with SIM 26-6).
Remedy: Check the destination of the FAX-BOX. Check the machine destination with SIM 26-6. Use a proper combination of the machine and the FAX-BOX.

Code: F7-01

Description: FAX board EEPROM read/write error
ACK from the EEPROM cannot be checked.
Causes: EEPROM trouble FAX PWB EEPROM access circuit trouble
Remedy: Replace the EEPROM. Re-setup the soft SW.

Code: H2-00

Description: Thermistor open/Fusing unit not installed (HL1)
Thermistor open (An input voltage of 4.6V or above is detected.) Fusing unit not installed
Causes: Thermistor trouble. Control PWB trouble Improper connection of the fusing section connector. AC power trouble. Fusing unit not installed.
Remedy: Check the harness and the connector between the thermistor and the control PWB. Use SIM 14 to clear the self diag display.

Code: H2-01

Description: Thermistor open/Fusing unit not installed (HL2)
Thermistor open (An input voltage of 4.6V or above is detected.) Fusing unit not installed
Causes: Thermistor trouble Control PWB trouble Improper. connection of the fusing section connector. AC power trouble. Fusing unit not installed.
Remedy: Check the harness and the connector between the thermistor and the control PWB. Use SIM 14 to clear the self diag display.

Code: H2-02

Description: Thermistor open/Fusing unit not installed (HL3)
Thermistor open (An input voltage of 4.6V or above is detected.) Fusing unit not installed
Causes: Thermistor trouble. Control PWB trouble. Improper connection of the fusing section connector. AC power trouble. Fusing unit not installed.
Remedy: Check the harness and the connector between the thermistor and the control PWB. Use SIM 14 to clear the self diag display.

Code: H3-00

Description: Fusing section high temperature trouble (HL1)
The fusing temperature exceeds 241.5 °C. (An input voltage of 1.3V or less is detected.) When fusing temperature control is started and a temperature of 242 °C is detected 3 times continuously in sampling of 250 msec interval. (In the interval of 150ms)
Causes: Thermistor trouble Control PWB trouble Improper connection of the fusing section connector AC power trouble
Remedy: Use SIM 5-2 to check flashing of the heater lamp. When the lamp flashes normally. • Check the thermistor and the harness. • Check the thermistor input circuit on the control PWB. When the lamp keeps ON. • Check the AC PWB and the lamp control circuit on the control PWB. Use SIM 14 to cancel the trouble

Code: H3-01

Description: Fusing section high temperature trouble (HL2)
The fusing temperature exceeds 241.5 °C. (An input voltage of 1.3V or less is detected.) When fusing temperature control is started and a temperature of 242 °C is detected 3 times continuously in sampling of 250 msec interval. (In the interval of 150ms)
Causes: Thermistor trouble. Control PWB trouble.
Improper connection of the fusing section
connector. AC power trouble.
Remedy: Use SIM 5-2 to check flashing of the heater lamp. When the lamp flashes normally. • Check the thermistor and the harness. • Check the thermistor input circuit on the control PWB. When the lamp keeps ON. • Check the AC PWB and the lamp control circuit on the control PWB. Use SIM 14 to cancel the trouble
Đăng ký nhận bản tin Đăng ký nhận bản tin Đăng ký nhận bản tin Đăng ký nhận bản tin
Đăng ký nhận bản tin
Nhận ưu đãi sớm nhất khi chương trình diễn ra

Đăng ký nhận bản tin

Việc cho phép sử dụng cookie sẽ giúp cải thiện trải nghiệm của bạn trên trang web này. Chính sách cookie