Thương hiệu phân phối chính hãng
Giỏ hàng

Mã lỗi Toshiba e-Studio 2505 — Trang 5/6

Code: E714

Description: Feed signal reception jam
Causes: Original empty sensor
Remedy: Original empty sensor • Sensor check (Perform the input check: 03-[8]/[B]) • Lever check • Connector check • Harness check ADF board • Board check • Connector check (PA4) • Harness check

Code: E721

Description: Jam not reaching the read sensor
Causes: Read sensor ADF board Transport roller-1 Transport roller-2
Remedy: Transport roller-1 / Transport roller-2 Clean the transport roller-1 and transport roller-2 if they are stained. Read sensor • Sensor check (Perform the input check: 03-[8]/[G]) • Connector check • Harness check ADF board • Board check • Connector check (PA4) • Harness check

Code: E725

Description: Stop jam at the read sensor
Causes: Read sensor ADF board Transport roller-2 Replace it if it is worn out.
Remedy: Transport roller-2 Clean the transport roller-2 if they are stained. Read sensor • Sensor check (Perform the input check: 03-[8]/[G]) • Connector check • Harness check ADF board • Board check • Connector check (PA4) • Harness check

Code: EAD0

Description: Print end command time-out jam
Causes: Main motor MAIN board
Remedy: dure Check item Result Measure Next Step 1 Is the main motor working? (Perform the output check in the test mode: 03-101/ 151) Yes Is the main motor rotating normally? (Perform the output check:03-101/151) 2 No • Replace the main motor. 2 MAIN board Check if the conductor pattern on the MAIN board is short circuited or open circuited.

Code: EB50

Description: Paper left on the transport path due to multiple feeding. The multiple feeding of preceding paper caused the misfeeding of upcoming paper.
Causes: Registration sensor MAIN board Rollers on the transport path
Remedy: 1 Open the right cover. Is there any paper on the transport path? Remove paper if there is any on the transport path. 2 2 Is the registration sensor working? (Perform the input check: 03-[A]/[A]) Yes Check the rollers. Replace them if they are worn out No 3 3 MAIN board 1. Check if the connector CN22 on the MAIN board is disconnected. 2. Check if the connector pins are disconnected or the harnesses are open circuited. 3. Check if the conductor patterns on the MAIN board are short circuited or open circuited.

Code: EB60

Description: Paper left on the transport path due to multiple feeding. The multiple feeding of preceding paper caused the misfeeding of upcoming paper (re-detection after no jam is detected at EB50 error)
Causes: Registration sensor MAIN board Rollers on the transport path
Remedy: 1 Open the right cover. Is there any paper on the transport path? Yes Remove the paper. No 2 2 Is the registration sensor working? (Perform the input check in the test mode: 03-[A]/ [A]) Yes 3 No • Check if the connector CN22 on the MAIN board is disconnected. • Check if the connector of the registration sensor is disconnected. • Check if the connector pins are disconnected and the harnesses are open circuited. • Check if the conductor pattern on the MAIN board is short circuited or open circuited. • Replace the registration sensor. • Replace the MAIN board. 3 Roller • Check the rollers. Replace them if they are worn out.

Code: F070

Description: Communication error between system CPU and main CPU
Causes: MAIN board
Remedy: Check ROM version Check the version of the system ROM. Check the version of the engine ROM version. Board check

Code: F090

Description: Memory abnormality on the MAIN board.
Causes: Memory (IC24) on the MAIN board
Remedy: 1. Turn the power off, and start up the Setting Mode (08). 2. When ¡§TEST MODE D¡¨ is displayed on the control panel, key in code: 9080 and press the [START] key. Notes: Code: 9080 cannot be keyed in except when 08-9010 is ON. To set the 08-9010, if this is the case, key in 08-9010-[START] -CLEAR]-key in [1]-[OK]. 3. When ¡§SELECT DESTINATION¡¨ is displayed, use the keys to select a direction and press the [OK] key. 4. When MC=9080¡¨ is displayed on the control panel, press the [OK] key. To cancel, press the [CANCEL] key. 5. If flash memory clear ends normally,INITIALISE=OK¡¨ is displayed on the control panel, it automatically changes to the initial screen of the 08 mode. 6. Perform the initialization after the software version upgrade (08-9030). 7. Display the serial number (08-9601) and check the serial number. Key in the correct serial number using 08-9601 if the serial number is different from the serial number on the identification plate on the back cover. 8. Set the 08-9010 to. 9. Turn the power off and then on, if the error is not corrected, replace the flash memory on the main board.
Đăng ký nhận bản tin Đăng ký nhận bản tin Đăng ký nhận bản tin Đăng ký nhận bản tin
Đăng ký nhận bản tin
Nhận ưu đãi sớm nhất khi chương trình diễn ra

Đăng ký nhận bản tin

Việc cho phép sử dụng cookie sẽ giúp cải thiện trải nghiệm của bạn trên trang web này. Chính sách cookie