Thương hiệu phân phối chính hãng
Giỏ hàng

Mã lỗi Toshiba e-Studio 2505 — Trang 4/6

Code: E110

Description: Jam not reaching the registration sensor
Causes: Registration sensor ADU clutch MAIN board Rollers in the ADU
Remedy: 1 Open the ADU. Is there any paper in front of the registration sensor? Yes Remove the paper. No 2 2 Is the registration sensor working? (Perform the input check in the test mode: 03-[A]/ [A]) Yes 3 No • Check if the connector of the registration sensor is disconnected. • Check if the connector CN22 on the MAIN board is disconnected. • Check if the connector pins are disconnected and the harnesses are open circuited. • Check if the conductor pattern on the MAIN board is short circuited or open circuited. • Replace the registration sensor. 3 Is the ADU clutch working? (Perform the output check in the test mode: 03-222) Yes 4 No • Check if the connector of the ADU clutch is disconnected. • Check if the connector CN17 on the MAIN board is disconnected. • Check if the connector pins are disconnected and the harnesses are open circuited. • Check if the conductor pattern on the MAIN board is short circuited or open circuited. • Replace the ADU clutch. 4 Rollers in the ADU • Check the rollers in the ADU. Replace them if they are worn out.

Code: E120

Description: Bypass misfeeding. Jam not reaching the registration sensor
Causes: MAIN board Bypass feed clutch Bypass paper sensor Bypass feed roller Separation pad
Remedy: 1 Open the right cover. Is there any paper on the transport path? Yes Remove the paper. No 2 2 Is the bypass feed clutch working? (Perform the output check in the test mode: 03-204) Is the bypass paper sensor working? (Perform the input check in the test mode: 03-[4]/[F]) Yes 3 No • Check if the connector of the bypass feed clutch and bypass paper sensor are disconnected. • Check if the connector CN22 on the MAIN board is disconnected. • Check if the connector pins are disconnected and the harnesses are open circuited. • Check if the conductor pattern on the MAIN board is short circuited or open circuited. • Replace the bypass feed clutch and bypass paper sensor. • Replace the MAIN board. 3 Bypass feed roller Bypass separation pad • Check the bypass feed roller and bypass separation pad. Replace them if they are worn out.

Code: E130

Description: 1st drawer misfeeding. Jam not reaching the registration sensor
Causes: MAIN board Upper drawer feed clutch Upper drawer feed roller Separation roller
Remedy: 1 Open the right cover. Is there any paper on the transport path? Yes Remove the paper. No 2 2 Is the drawer feed clutch working? (Perform the output check in the test mode: 03-201) Yes 4 No • Check if the connector of the drawer feed clutch is disconnected. • Check if the connector CN22 on the MAIN board is disconnected. • Check if the connector pins are disconnected and the harnesses are open circuited. • Check if the conductor pattern on the MAIN board is short circuited or open circuited. • Replace the drawer feed clutch. • Replace the MAIN board. 3 1st drawer feed roller Separation roller • Check the drawer feed roller and separation roller. Replace them if they are worn out.

Code: E410

Description: Toner supply cover opened during printing. Toner supply cover open jam
Causes: Toner supply cover opening/ closing switch MAIN board
Remedy: 1 Is the toner supply cover open? Yes Close the cover. No 2 2 Is the toner supply cover opening/closing switch working? (Perform the input check in the test mode: 03-[A]/ [D]) Yes 3 No • Check if the connector of the toner supply cover opening/closing switch is disconnected. • Check if the connector CN15 on the MAIN board is disconnected. • Check if the connector pins are disconnected and the harnesses are open circuited. • Check if the conductor pattern on the MAIN board is short circuited or open circuited. • Replace the toner supply cover opening/ closing switch. 3 Is the voltage of 24V being supplied from the power supply unit? (Perform the input check in the test mode: 03-[6]/ [A]) Yes 4 No • Check if the connector for 24 V power supply is disconnected. • Check if the connector CN25 on the MAIN board is disconnected. • Check if the connector pins are disconnected and the harnesses are open circuited. 4 MAIN board • Check if the conductor pattern on the MAIN board is short circuited or open circuited. • Replace the MAIN board.

Code: E430

Description: Right cover opened during printing (When ADU is installed). Right cover open jam
Causes: Right cover opening/closing switch MAIN board
Remedy: 1 Is the right cover open? Yes Remove the paper if there is any, then close the right cover. No 2 2 Is the right cover opening/ closing switch working? (Perform the input check in the test mode: 03-[6]/ [A]) Yes 3 No • Check if the connector of the right cover opening/closing switch is disconnected. • Check if the connector CN25 on the MAIN board is disconnected. • Check if the connector pins are disconnected and the harnesses are open circuited. • Check if the conductor patterns on the MAIN board are short circuited or open circuited. • Replace the right cover opening/closing switch. 3 MAIN board • Replace the MAIN board.

Code: E510

Description: ADU stack jam (paper not reaching the ADU transfer sensor. Jam not reaching the ADU transfer sensor
Causes: ADU transfer sensor MAIN board Exit motor ADU exit sensor Rollers in the ADU Exit roller
Remedy: 1 Open the right cover. Is there any paper in front of the ADU transfer sensor? Yes Remove the paper. No 2 2 Is the ADU transfer sensor working? (Perform the input check in the test mode: 03-[FAX]OFF/[1]/ [C]) Yes 3 No • Check if the connector of the ADU transfer sensor is disconnected. • Check if the connector CN17 on the MAIN board is disconnected. • Check if the connector pins are disconnected and the harnesses are open circuited. • Check if the conductor patterns on the MAIN board are short circuited or open circuited. • Replace the ADU transfer sensor. • Replace the MAIN board. 3 Is the exit motor (rotating in reverse) working? (Perform the output check in the test mode: 03-121/ 171) Yes 4 No • Check if the connector of the exit motor is disconnected. • Check if the connector pins are disconnected and the harnesses are open circuited. • Replace the exit motor. • Replace the MAIN board. 4 ADU • Check the rollers in the ADU and the exit roller of the equipment. Replace them if they are worn out.

Code: E550

Description: Paper remaining on the transport path
Causes: Sensor Refer to the following table MAIN board
Remedy: 1 Open the cover of the unit/ area whose picture is blinking on the control panel. Is there any paper on the transport path? Yes Remove the paper. No 2 2 Is the sensor in the jamming area working? (Perform the input check in the test mode: refer to the following table) Yes 3 No • Check if the connector of the sensor is disconnected. • Check if any of the connectors on the MAIN board is disconnected. • Check if the connector pins are disconnected and the harnesses are open circuited. • Check if the conductor pattern on the MAIN board is short circuited or open circuited. • Replace the sensor. 3 MAIN board • Replace the MAIN board.

Code: E552

Description: Paper remaining jam on the transport path (when the cover is closed).
Causes: Sensor in the jamming area Refer to the table below. MAIN board
Remedy: 1 Jamming transport path Open the cover of the unit/area whose picture is flashing on the control panel and remove any paper on the transport path. 2 Sensor in the jamming area • Sensor check (Refer to the table below) • Harness check • Connector check 3 MAIN board • Harness check • Connector check • Board check
Đăng ký nhận bản tin Đăng ký nhận bản tin Đăng ký nhận bản tin Đăng ký nhận bản tin
Đăng ký nhận bản tin
Nhận ưu đãi sớm nhất khi chương trình diễn ra

Đăng ký nhận bản tin

Việc cho phép sử dụng cookie sẽ giúp cải thiện trải nghiệm của bạn trên trang web này. Chính sách cookie