• Code: E064
• Description: Incorrect paper size setting for PFP lower drawer: The size of paper in the 4th drawer differs from size setting of the equipment.
• Causes:
• Remedy: Paper size If any paper remains in the equipment or drawer, remove it. Match the paper size of the drawer setting and the one in the drawer. * Paper size detection is performed at the first sheet of paper when the drawer is opened or closed, or when the power of the equipment is turned ON.

• Code: E065
• Description: Incorrect paper size setting for bypass tray: The size of paper in the bypass tray differs from size setting of the equipment.
• Causes:
• Remedy: Paper size If any paper remains in the equipment or drawer, remove it. Match the paper size of the drawer setting and the one in the drawer. * Paper size detection is performed at the first sheet of paper when the drawer is opened or closed, or when the power of the equipment is turned ON.

• Code: E090
• Description: Image data delay jam: Image data to be printed cannot be prepared.
• Causes: SYS board LGC board HDD Main memory
• Remedy: Other • Remove the paper remained in front of the registration sensor) • Check if the error is cleared by turning the power OFF and then back ON. SYS board • Connector check • Main memory check • Board check LGC board • Connector check • Board check HDD • Connector check • HDD check

• Code: E0A0
• Description: Image transport ready time-out jam
• Causes: LGC board
• Remedy: LGC board • Connector check • Harness check (SYS board - LGC board)

• Code: E110
• Description: ADU misfeeding (Paper not reaching the registration sensor): The paper which has passed through ADU does not reach the registration sensor during duplex printing.
• Causes: ADU motor LGC board ADU board Rollers in the ADU
• Remedy: 1 Open the ADU. Is there any paper in front of the registration sensor? Yes Remove the paper. No 2 2 Is the registration sensor working? (Perform the input check in the test mode: FS-03- [ALL]OFF/[9]/[A]) Yes 3 No • Check if the connector of the 1st transport sensor is disconnected. • Check if the connector CN318 on the LGC board is disconnected. • Check if the connector pins are disconnected and the harnesses are open circuited. • Check if the conductor pattern on the LGC board is short circuited or open circuited. • Replace the 1st registration sensor. • Replace the LGC board. 3 Is the ADU clutch working? (Perform the output check in the test mode: FS-03-110/160) Yes 4 No • Check if the connector of the ADU motor is disconnected. (J691) • Check if the connector CN321 on the LGC board is disconnected. • Check if the connector CN422 and CN420 on the ADU board is disconnected. • Check if the connector pins are disconnected and the harnesses are open circuited. • Check if the conductor pattern on the LGC board is short circuited or open circuited. • Replace the ADU motor. • Replace the LGC board. • Replace the ADU board. 4 Rollers in the ADU • Check the rollers in the ADU. Replace them if they are worn out.

• Code: E120
• Description: Bypass misfeeding (Paper not reaching the 1st transport sensor): The paper fed from the bypass tray does not reach the 1st transport sensor.
• Causes: 1st transport sensor LGC board Bypass feed clutch Bypass paper sensor Bypass feed roller Bypass separation roller
• Remedy: 1 Open the Automatic duplexing unit. Is there any paper in front of the 1st transport sensor? Yes Remove the paper. No 2 2 Is the 1st transport sensor working? (Perform the input check in the test mode: FS-03- [ALL]OFF/[9]/[B]) Yes 3 No • Check if the connector of the 1st transport sensor is disconnected. (J661, J659) • Check if the connector CN316 on the LGC board is disconnected. • Check if the connector pins are disconnected and the harnesses are open circuited. • Check if the conductor pattern on the LGC board is short circuited or open circuited. • Replace the 1st transport sensor. • Replace the LGC board. 3 Is the bypass feed clutch working? (Perform the output check in the test mode: 03-204) Is the bypass paper sensor working? (Perform the input check in the test mode: FS-03-[ALL]OFF/ [2]/[E]) Yes 4 No • Check if the connector of the bypass feed clutch and bypass paper sensor are disconnected. (J695, J696, J699) • Check if the connector CN321 on the LGC board is disconnected. • Check if the connector pins are disconnected and the harnesses are open circuited. • Check if the conductor pattern on the LGC board is short circuited or open circuited. • Replace the bypass feed clutch and bypass paper sensor. • Replace the LGC board. 4 Bypass feed roller Separation pad • Check the bypass feed roller and separation roller. Replace them if they are worn out.

• Code: E130
• Description: 1st drawer misfeeding (Paper not reaching the 1st transport sensor): The paper fed from the 1st drawer does not reach the 1st transport sensor.
• Causes: 1st transport sensor. LGC board 1st drawer feed clutch 1st drawer feed roller 1st drawer separation roller 1st drawer pickup roller
• Remedy: 1 Open the Automatic duplexing unit. Is there any paper in front of the 1st transport sensor? Yes Remove the paper. No 2 2 Is the 1st transport sensor working? (Perform the input check in the test mode: FS-03- [ALL]OFF/[9]/[B]) Yes 3 No • Check if the connector of the 1st transport sensor is disconnected. (J661, J659) • Check if the connector CN318 on the LGC board is disconnected. • Check if the connector pins are disconnected and the harnesses are open circuited. • Check if the conductor pattern on the LGC board is short circuited or open circuited. • Replace the 1st transport sensor. • Replace the LGC board. 3 Is the 1st drawer feed clutch working? (Perform the output check in the test mode: FS-03- 201) Yes 4 No • Check if the connector of the 1st drawer feed clutch is disconnected. (J666) • Check if the connector CN316 on the LGC board is disconnected. • Check if the connector pins are disconnected and the harnesses are open circuited. • Check if the conductor pattern on the LGC board is short circuited or open circuited. • Replace the 1st drawer feed clutch. • Replace the LGC board. 4 1st drawer feed roller Separation roller Pickup roller • Check the 1st drawer feed roller, separation roller and pickup roller. Replace them if they are worn out.

• Code: E140
• Description: 2nd drawer misfeeding (Paper not reaching the 2nd transport sensor): The paper fed from the 2nd drawer does not reach the 2nd transport sensor.
• Causes: 2nd transport sensor LGC board 2nd drawer feed clutch 2nd drawer feed roller 2nd drawer separation roller 2nd drawer pickup roller
• Remedy: 1 Open the feed cover. Is there any paper in front of the 2nd transport sensor? Yes Remove the paper. No 2 2 Is the 2nd transport sensor working? (Perform the input check in the test mode: FS-03- [F3]ON/[4]/[D]) Yes 3 No • Check if the connector of the 2nd transport sensor is disconnected. (J676) • Check if the connector CN318 on the LGC board is disconnected. • Check if the connector pins are disconnected and the harnesses are open circuited. • Check if the conductor pattern on the LGC board is short circuited or open circuited. • Replace the 2nd transport sensor. • Replace the LGC board. 3 Is the 2nd drawer feed clutch working? (Perform the output check in the test mode: FS-03- 202) Yes 4 No • Check if the connector of the 2nd drawer feed clutch is disconnected. • Check if the connector CN316 on the LGC board is disconnected. • Check if the connector pins are disconnected and the harnesses are open circuited. • Check if the conductor pattern on the LGC board is short circuited or open circuited. • Replace the 2nd drawer feed clutch. • Replace the LGC board. 4 2nd drawer feed roller Separation roller Pickup roller • Check the 2nd drawer feed roller, separation roller and pickup roller. Replace them if they are worn out.