• Code: E065
• Description: Incorrect paper size setting for bypass tray: The size of paper in the bypass tray differs from size setting of the equipment
• Causes:
• Remedy: Paper size If any paper remains in the equipment or drawer, remove it. Match the paper size of the drawer setting and the one in the drawer. * Paper size detection is performed at the first sheet of paper when the drawer is opened or closed, or when the power of the equipment is turned ON.

• Code: E090
• Description: HDD abnormality causes jam: Image data to be printed cannot be prepared.
• Causes:
• Remedy:

• Code: E110
• Description: ADU misfeeding (Paper not reaching the registration sensor): The paper which has passed through ADU does not reach the registration sensor during duplex printing
• Causes: ADU clutch LGC board Rollers in the ADU
• Remedy: 1 Open the ADU. Is there any paper in front of the registraton sensor? Yes Remove the paper. No 2 2 Is the registraton sensor working? (Perform the input check in the test mode: 03- [FAX]ON/[9]/[A]) Yes 3 No • Check if the connector of the 1st transport sensor is disconnected. • Check if the connector CN316 on the LGC board is disconnected. • Check if the connector pins are disconnected and the harnesses are open circuited. • Check if the conductor pattern on the LGC board is short circuited or open circuited. • Replace the 1st registration sensor. • Replace the LGC board. 3 Is the ADU clutch working? (Perform the output check in the test mode: 03-222) Yes 4 No • Check if the connector of the ADU clutch is disconnected. • Check if the connector CN304 on the LGC board is disconnected. • Check if the connector pins are disconnected and the harnesses are open circuited. • Check if the conductor pattern on the LGC board is short circuited or open circuited. • Replace the ADU clutch. • Replace the LGC board. 4 Rollers in the ADU • Check the rollers in the ADU. Replace them if they are worn out.

• Code: E120
• Description: Bypass misfeeding (Paper not reaching the 1st transport sensor): The paper fed from the bypass tray does not reach the 1st transport sensor
• Causes: 1st transport sensor LGC board Bypass feed clutch Bypass paper sensor Bypass feed roller Separation pad
• Remedy: 1 Open the Automatic duplexing unit. Is there any paper in front of the 1st transport sensor? Yes Remove the paper. No 2 2 Is the 1st transport sensor working? (Perform the input check in the test mode: 03- [FAX]OFF/[6]/[A]) Yes 3 No • Check if the connector of the 1st transport sensor is disconnected. • Check if the connector CN316 on the LGC board is disconnected. • Check if the connector pins are disconnected and the harnesses are open circuited. • Check if the conductor pattern on the LGC board is short circuited or open circuited. • Replace the 1st transport sensor. • Replace the LGC board. 3 Is the bypass feed clutch working? (Perform the output check in the test mode: 03-204) Is the bypass paper sensor working? (Perform the input check in the test mode: 03-[FAX]OFF/[1]/ [D]) Yes 4 No • Check if the connector of the bypass feed clutch and bypass paper sensor are disconnected. • Check if the connector CN311 on the LGC board is disconnected. • Check if the connector pins are disconnected and the harnesses are open circuited. • Check if the conductor pattern on the LGC board is short circuited or open circuited. • Replace the bypass feed clutch and bypass paper sensor. • Replace the LGC board. 4 Bypass feed roller Separation pad • Check the bypass feed roller and separation pad. Replace them if they are worn out.

• Code: E130
• Description: Upper drawer misfeeding (Paper not reaching the 1st transport sensor): The paper fed from the upper drawer does not reach the 1st transport sensor.
• Causes: 1st transport sensor. LGC board Upper drawer feed clutch Upper drawer feed roller Separation roller Pickup roller
• Remedy: 1 Open the Automatic duplexing unit. Is there any paper in front of the 1st transport sensor? Yes Remove the paper. No 2 2 Is the 1st transport sensor working? (Perform the input check in the test mode: 03- [FAX]OFF/[6]/[A]) Yes 3 No • Check if the connector of the 1st transport sensor is disconnected. • Check if the connector CN316 on the LGC board is disconnected. • Check if the connector pins are disconnected and the harnesses are open circuited. • Check if the conductor pattern on the LGC board is short circuited or open circuited. • Replace the 1st transport sensor. • Replace the LGC board. 3 Is the upper drawer feed clutch working? (Perform the output check in the test mode: 03-201) Yes 4 No • Check if the connector of the upper drawer feed clutch is disconnected. • Check if the connector CN315 on the LGC board is disconnected. • Check if the connector pins are disconnected and the harnesses are open circuited. • Check if the conductor pattern on the LGC board is short circuited or open circuited. • Replace the upper drawer feed clutch. • Replace the LGC board. 4 Upper drawer feed roller Separation roller • Check the upper drawer feed roller, separation roller and pickup roller. Replace them if they are worn out.

• Code: E140
• Description: Lower drawer misfeeding (Paper not reaching the 2nd transport sensor): The paper fed from the lower drawer does not reach the 2nd transport sensor.
• Causes: 2nd transport sensor LGC board Lower drawer feed clutch Lower drawer feed roller Separation roller Pickup roller
• Remedy: 1 Open the feed cover. Is there any paper in front of the 2nd transport sensor? Yes Remove the paper. No 2 2 Is the 2nd transport sensor working? (Perform the input check in the test mode: 03- [FAX]OFF/[7]/[A]) Yes 3 No • Check if the connector of the 2nd transport sensor is disconnected. • Check if the connector CN316 on the LGC board is disconnected. • Check if the connector pins are disconnected and the harnesses are open circuited. • Check if the conductor pattern on the LGC board is short circuited or open circuited. • Replace the 2nd transport sensor. • Replace the LGC board. 3 Is the lower drawer feed clutch working? (Perform the output check in the test mode: 03-202) Yes 4 No • Check if the connector of the lower drawer feed clutch is disconnected. • Check if the connector CN315 on the LGC board is disconnected. • Check if the connector pins are disconnected and the harnesses are open circuited. • Check if the conductor pattern on the LGC board is short circuited or open circuited. • Replace the lower drawer feed clutch. • Replace the LGC board. 4 Lower drawer feed roller Separation roller Pickup roller • Check the lower drawer feed roller, separation roller and pickup roller. Replace them if they are worn out.

• Code: E150
• Description: PFP upper drawer misfeeding (Paper not reaching the PFP upper drawer feed sensor): The paper fed from the PFP upper drawer does not reach the PFP upper drawer feed sensor.
• Causes: PFP upper drawer feed sensor PFP board LGC board PFP upper drawer feed clutch PFP upper drawer feed roller Separation roller
• Remedy: 1 Open the PFP side cover. Is there any paper in front of the PFP upper drawer feed sensor? Yes Remove the paper. No 2 2 Is the PFP upper drawer feed sensor working? (Perform the input check in the test mode: 03- [FAX]OFF/[2]/[B]) Yes 3 No • Check if the connector of the PFP upper drawer feed sensor is disconnected. • Check if either of the connectors CN241 or CN243 on the PFP board is disconnected. • Check if the connector CN318 on the LGC board is disconnected. • Check if the connector pins are disconnected and the harnesses are open circuited. • Check if the conductor patterns on the PFP board and LGC board are short circuited or open circuited. • Replace the PFP upper drawer feed sensor. • Replace the PFP board. • Replace the LGC board. 3 Is the PFP upper drawer feed clutch working? (Perform the output check in the test mode: 03-226) Yes 4 No • Check if the connector of the PFP upper drawer feed clutch is disconnected. • Check if any of the connectors CN241 and CN247 on the PFP board is disconnected. • Check if the connector CN318 on the LGC board is disconnected. • Check if the connector pins are disconnected and the harnesses are open circuited. • Check if the conductor patterns on the PFP board and LGC board are short circuited or open circuited. • Replace the PFP upper drawer feed clutch. • Replace the PFP board. • Replace the LGC board. 4 PFP upper drawer feed roller Separation roller Pickup roller • Check the PFP upper drawer feed roller, separation roller and pickup roller. Replace them if they are worn out.

• Code: E160
• Description: PFP lower drawer misfeeding (Paper not reaching the PFP lower drawer feed sensor): The paper fed from the PFP lower drawer does not reach the PFP lower drawer feed senso
• Causes: PFP lower drawer feed sensor. PFP board LGC board PFP lower drawer feed clutch PFP lower drawer feed roller, Separation roller Pickup roller
• Remedy: 1 Open the PFP side cover. Is there any paper in front of the PFP lower drawer feed sensor? Yes Remove the paper. No 2 2 Is the PFP lower drawer feed sensor working? (Perform the input check in the test mode: 03- [FAX]OFF/[3]/[B]) Yes 3 No • Check if the connector of the PFP lower drawer feed sensor is disconnected. • Check if either of the connectors CN241 or CN243 on the PFP board is disconnected. • Check if the connector CN318 on the LGC board is disconnected. • Check if the connector pins are disconnected and the harnesses are open circuited. • Check if the conductor patterns on the PFP board and LGC board are short circuited or open circuited. • Replace the PFP lower drawer feed sensor. • Replace the PFP board. • Replace the LGC board. 3 Is the PFP lower drawer feed clutch working? (Perform the output check in the test mode: 03-228) Yes 4 No • Check if the connector of the PFP lower drawer feed clutch is disconnected. • Check if any of the connectors CN241 and CN248 on the PFP board is disconnected. • Check if the connector CN318 on the LGC board is disconnected. • Check if the connector pins are disconnected and the harnesses are open circuited. • Check if the conductor patterns on the PFP board and LGC board are short circuited or open circuited. • Replace the PFP lower drawer feed clutch. • Replace the PFP board. • Replace the LGC board. 4 PFP lower drawer feed roller Separation roller Pickup roller • Check the PFP lower drawer feed roller, separation roller and pickup roller. Replace them if they are worn out.