Thương hiệu phân phối chính hãng
Giỏ hàng

Mã lỗi Toshiba e-Studio 3508A — Trang 13/26

Code: E150

Description: PFP upper drawer misfeeding (Paper not reaching the PFP upper drawer feed sensor): The paper fed from the PFP upper drawer does not reach the PFP upper drawer feed sensor.
Causes: PFP upper drawer feed sensor PFP board LGC board PFP upper drawer feed clutch PFP upper drawer feed roller PFP upper drawer separation roller
Remedy: 1 Open the PFP side cover. Is there any paper in front of the PFP upper drawer feed sensor? Yes Remove the paper. No 2 2 Is the PFP upper drawer feed sensor working? (Perform the input check in the test mode: FS-03- [F3]ON/[0]/[C]) Yes 3 No • Check if the connector of the PFP upper drawer feed sensor is disconnected. • Check if either of the connectors CN241 or CN247 on the PFP board is disconnected. • Check if the connector CN315 on the LGC board is disconnected. • Check if the connector pins are disconnected and the harnesses are open circuited. • Check if the conductor patterns on the PFP board and LGC board are short circuited or open circuited. • Replace the PFP upper drawer feed sensor. • Replace the PFP board. • Replace the LGC board. 3 Is the PFP upper drawer feed clutch working? (Perform the output check in the test mode: FS-03- 226) Yes 4 No • Check if the connector of the PFP upper drawer feed clutch is disconnected. • Check if any of the connectors CN241 and CN246 on the PFP board is disconnected. • Check if the connector CN315 on the LGC board is disconnected. • Check if the connector pins are disconnected and the harnesses are open circuited. • Check if the conductor patterns on the PFP board and LGC board are short circuited or open circuited. • Replace the PFP upper drawer feed clutch. • Replace the PFP board. • Replace the LGC board. 4 PFP upper drawer feed roller Separation roller Pickup roller • Check the PFP upper drawer feed roller, separation roller and pickup roller. Replace them if they are worn out.

Code: E160

Description: PFP lower drawer misfeeding (Paper not reaching the PFP lower drawer feed sensor): The paper fed from the PFP lower drawer does not reach the PFP lower drawer feed sensor.
Causes: PFP lower drawer feed sensor. PFP board LGC board PFP lower drawer feed clutch PFP lower drawer feed roller, PFP lower drawer separation roller PFP lower drawer pickup roller
Remedy: 1 Open the PFP side cover. Is there any paper in front of the PFP lower drawer feed sensor? Yes Remove the paper. No 2 2 Is the PFP lower drawer feed sensor working? (Perform the input check in the test mode: FS-03- [F3]ON/[0]/[D]) Yes 3 No • Check if the connector of the PFP lower drawer feed sensor is disconnected. • Check if either of the connectors CN241 or CN247 on the PFP board is disconnected. • Check if the connector CN315 on the LGC board is disconnected. • Check if the connector pins are disconnected and the harnesses are open circuited. • Check if the conductor patterns on the PFP board and LGC board are short circuited or open circuited. • Replace the PFP lower drawer feed sensor. • Replace the PFP board. • Replace the LGC board. 3 Is the PFP lower drawer feed clutch working? (Perform the output check in the test mode: FS-03- 228) Yes 4 No • Check if the connector of the PFP lower drawer feed clutch is disconnected. • Check if any of the connectors CN241 and CN246 on the PFP board is disconnected. • Check if the connector CN315 on the LGC board is disconnected. • Check if the connector pins are disconnected and the harnesses are open circuited. • Check if the conductor patterns on the PFP board and LGC board are short circuited or open circuited. • Replace the PFP lower drawer feed clutch. • Replace the PFP board. • Replace the LGC board. 4 PFP lower drawer feed roller Separation roller Pickup roller • Check the PFP lower drawer feed roller, separation roller and pickup roller. Replace them if they are worn out.

Code: E190

Description: LCF misfeeding (Paper not reaching the LCF transport sensor): The paper fed from the LCF does not reach the LCF feed sensor.
Causes: LCF transport sensor LCF board LGC board LCF feed clutch LCF feed roller LCF separation roller LCF pickup roller
Remedy: 1 Open the LCF side cover. Is there any paper in front of the LCF transport sensor? Yes Remove the paper. No 2 2 Is the LCF transport sensor working? (Perform the input check in the test mode: FS-03- [F1]ON/[9]/[F]) Yes 3 No • Check if the connector of the LCF transport sensor is disconnected. • Check if either of the connectors CN1 or CN2 on the LCF board is disconnected. • Check if the connector CN315 on the LGC board is disconnected. • Check if the connector pins are disconnected and the harnesses are open circuited. • Check if the conductor patterns on the LCF board and LGC board are short circuited or open circuited. • Replace the LCF transport sensor. • Replace the LCF board. • Replace the LGC board. 3 Is the LCF feed clutch working? (Perform the output check in the test mode: FS-03-209) Yes 4 No • Check if the connector of the LCF feed clutch is disconnected. • Check if any of the connectors CN1 and CN6 on the LCF board is disconnected. • Check if the connector CN315 on the LGC board is disconnected. • Check if the connector pins are disconnected and the harnesses are open circuited. • Check if the conductor patterns on the LCF board and LGC board are short circuited or open circuited. • Replace the LCF feed clutch. • Replace the LCF board. • Replace the LGC board. 4 LCF feed roller Separation roller Pickup roller • Check the LCF feed roller, separation roller and pickup roller. Replace them if they are worn out.

Code: E200

Description: 1st drawer transport jam (Paper not reaching the registration sensor): The paper does not reach the registration sensor after it has passed the 1st transport sensor.
Causes: Registration roller LGC board High-speed/low-speed transport clutches Feed roller
Remedy: 1 Open the Automatic duplexing unit. Is there paper in front of the registration sensor? Yes Remove the paper. No 2 2 Is the registration sensor working? (Perform the input check in the test mode: FS-03- [ALL]OFF/[9]/[A]) Yes 3 No • Check if the connector of the registration sensor is disconnected. • Check if the connector CN318 on the LGC board is disconnected. • Check if the connector pins are disconnected and the harnesses are open circuited • Check if the conductor pattern on the LGC board is short circuited or open circuited. • Replace the registration sensor. • Replace the LGC board. 3 Are the (high-speed/lowspeed) clutches working? (Perform the output check in the test mode: 03-203, 205) Yes 4 No • Check if the connectors of the (high-speed/ low-speed) transport clutches are disconnected. • Check if the connector CN318 on the LGC board is disconnected. • Check if the connector pins are disconnected and the harnesses are open circuited. • Check if the conductor pattern on the LGC board is short circuited or open circuited. • Replace the (high-speed/low-speed) transport clutches. • Replace the LGC board. 4 Feed roller Separation roller Pickup roller Transfer roller • Check the condition of the feed roller, separation roller and pickup roller of each paper source, and replace them if they are worn out. • Check the transport roller. Replace it if it is worn out.

Code: E210

Description: 2nd drawer transport jam (Paper not reaching the registration sensor): The paper does not reach the registration sensor after it has passed the 1st transport sensor.
Causes: Registration roller LGC board High-speed/low-speed transport clutches Feed roller
Remedy: 1 Open the Automatic duplexing unit. Is there paper in front of the registration sensor? Yes Remove the paper. No 2 2 Is the registration sensor working? (Perform the input check in the test mode: FS-03- [ALL]OFF/[9]/[A]) Yes 3 No • Check if the connector of the registration sensor is disconnected. • Check if the connector CN318 on the LGC board is disconnected. • Check if the connector pins are disconnected and the harnesses are open circuited • Check if the conductor pattern on the LGC board is short circuited or open circuited. • Replace the registration sensor. • Replace the LGC board. 3 Are the (high-speed/lowspeed) clutches working? (Perform the output check in the test mode: 03-203, 205) Yes 4 No • Check if the connectors of the (high-speed/ low-speed) transport clutches are disconnected. • Check if the connector CN318 on the LGC board is disconnected. • Check if the connector pins are disconnected and the harnesses are open circuited. • Check if the conductor pattern on the LGC board is short circuited or open circuited. • Replace the (high-speed/low-speed) transport clutches. • Replace the LGC board. 4 Feed roller Separation roller Pickup roller Transfer roller • Check the condition of the feed roller, separation roller and pickup roller of each paper source, and replace them if they are worn out. • Check the transport roller. Replace it if it is worn out.

Code: E220

Description: 2nd drawer transport jam (Paper not reaching the 1st transport sensor): The paper does not reach the 1st transport sensor after it has passed the lower drawer feed sensor.
Causes: 1st transport sensor LGC board Feed roller Separation roller Pickup roller Transfer roller
Remedy: 1 Open the Automatic duplexing unit. Is there paper in front of the 1st transport sensor? Yes Remove the paper. No 2 2 Is the 1st transport sensor working? (Perform the input check in the test mode: FS-03- [ALL]OFF/[9]/[B]) Yes 3 No • Check if the connector of the 1st transport sensor is disconnected. (J661, J659) • Check if the connector CN318 on the LGC board is disconnected. • Check if the connector pins are disconnected and the harnesses are open circuited. • Check if the conductor pattern on the LGC board is short circuited or open circuited. • Replace the 1st transport sensor. • Replace the LGC board. 3 Are the (high-speed/lowspeed) transport clutches working? (Perform the output check in the test mode: 03-203, 205) Yes 4 No • Check if the connectors of the (high-speed/ low-speed) transport clutches are disconnected. • Check if the connector CN318 on the LGC board is disconnected. • Check if the connector pins are disconnected and the harnesses are open circuited. • Check if the conductor pattern on the LGC board is short circuited or open circuited. • Replace the (high-speed/low-speed) transport clutches. • Replace the LGC board. 4 Feed roller Separation roller Pickup roller Transfer roller • Check the condition of the feed roller, separation roller and pickup roller of each paper source, and replace them if they are worn out. • Check the transport roller. Replace it if it is worn out.

Code: E270

Description: Bypass transport jam (paper not reaching the registration sensor): The paper does not reach the registration sensor after it has passed the 1st transport sensor.
Causes: Registration sensor. LGC board Bypass feed clutch Registration roller
Remedy: 1 Open the Automatic duplexing unit. Is there paper in front of the registration sensor? Yes Remove the paper. No 2 2 Is the registration sensor working? (Perform the input check in the test mode: FS-03- [ALL]OFF/[9]/[A]) Yes 3 No • Check if the connector of the registration sensor is disconnected. • Check if the connector CN318 on the LGC board is disconnected. • Check if the connector pins are disconnected and the harnesses are open circuited. • Check if the conductor pattern on the LGC board is short circuited or open circuited. • Replace the registration sensor. • Replace the LGC board. 3 Is the bypass feed clutch working? (Perform the output check in the test mode: FS-03- 204) Yes 4 No • Check if the connector of the bypass feed clutch is disconnected. • Check if the connector CN321 on the LGC board is disconnected. • Check if the connector pins are disconnected and the harnesses are open circuited. • Check if the conductor pattern on the LGC board is short circuited or open circuited. • Replace the bypass feed clutch. • Replace the LGC board. 4 Registration roller • Check the registration roller. Replace it if it is worn out.

Code: E300

Description: PFP upper drawer transport jam (Paper not reaching the registration sensor): The paper does not reach the registration sensor after it has passed the 1st transport sensor.
Causes: Registration roller LGC board High-speed/low-speed transport clutches Feed roller
Remedy: 1 Open the Automatic duplexing unit. Is there paper in front of the registration sensor? Yes Remove the paper. No 2 2 Is the registration sensor working? (Perform the input check in the test mode: FS-03- [ALL]OFF/[9]/[A]) Yes 3 No • Check if the connector of the registration sensor is disconnected. • Check if the connector CN318 on the LGC board is disconnected. • Check if the connector pins are disconnected and the harnesses are open circuited • Check if the conductor pattern on the LGC board is short circuited or open circuited. • Replace the registration sensor. • Replace the LGC board. 3 Are the (high-speed/lowspeed) clutches working? (Perform the output check in the test mode: 03-203, 205) Yes 4 No • Check if the connectors of the (high-speed/ low-speed) transport clutches are disconnected. • Check if the connector CN318 on the LGC board is disconnected. • Check if the connector pins are disconnected and the harnesses are open circuited. • Check if the conductor pattern on the LGC board is short circuited or open circuited. • Replace the (high-speed/low-speed) transport clutches. • Replace the LGC board. 4 Feed roller Separation roller Pickup roller Transfer roller • Check the condition of the feed roller, separation roller and pickup roller of each paper source, and replace them if they are worn out. • Check the transport roller. Replace it if it is worn out.
Đăng ký nhận bản tin Đăng ký nhận bản tin Đăng ký nhận bản tin Đăng ký nhận bản tin
Đăng ký nhận bản tin
Nhận ưu đãi sớm nhất khi chương trình diễn ra

Đăng ký nhận bản tin

Việc cho phép sử dụng cookie sẽ giúp cải thiện trải nghiệm của bạn trên trang web này. Chính sách cookie