Thương hiệu phân phối chính hãng
Giỏ hàng

Mã lỗi Toshiba e-Studio 3508A — Trang 12/26

Code: E064

Description: Incorrect paper size setting for PFP lower drawer: The size of paper in the 4th drawer differs from size setting of the equipment.
Causes:
Remedy: Paper size If any paper remains in the equipment or drawer, remove it. Match the paper size of the drawer setting and the one in the drawer. * Paper size detection is performed at the first sheet of paper when the drawer is opened or closed, or when the power of the equipment is turned ON.

Code: E065

Description: Incorrect paper size setting for bypass tray: The size of paper in the bypass tray differs from size setting of the equipment.
Causes:
Remedy: Paper size If any paper remains in the equipment or drawer, remove it. Match the paper size of the drawer setting and the one in the drawer. * Paper size detection is performed at the first sheet of paper when the drawer is opened or closed, or when the power of the equipment is turned ON.

Code: E090

Description: Image data delay jam: Image data to be printed cannot be prepared.
Causes: SYS board LGC board HDD Main memory
Remedy: Other • Remove the paper remained in front of the registration sensor) • Check if the error is cleared by turning the power OFF and then back ON. SYS board • Connector check • Main memory check • Board check LGC board • Connector check • Board check HDD • Connector check • HDD check

Code: E0A0

Description: Image transport ready time-out jam
Causes: LGC board
Remedy: LGC board • Connector check • Harness check (SYS board - LGC board)

Code: E110

Description: ADU misfeeding (Paper not reaching the registration sensor): The paper which has passed through ADU does not reach the registration sensor during duplex printing.
Causes: ADU motor LGC board ADU board Rollers in the ADU
Remedy: 1 Open the ADU. Is there any paper in front of the registration sensor? Yes Remove the paper. No 2 2 Is the registration sensor working? (Perform the input check in the test mode: FS-03- [ALL]OFF/[9]/[A]) Yes 3 No • Check if the connector of the 1st transport sensor is disconnected. • Check if the connector CN318 on the LGC board is disconnected. • Check if the connector pins are disconnected and the harnesses are open circuited. • Check if the conductor pattern on the LGC board is short circuited or open circuited. • Replace the 1st registration sensor. • Replace the LGC board. 3 Is the ADU clutch working? (Perform the output check in the test mode: FS-03-110/160) Yes 4 No • Check if the connector of the ADU motor is disconnected. (J691) • Check if the connector CN321 on the LGC board is disconnected. • Check if the connector CN422 and CN420 on the ADU board is disconnected. • Check if the connector pins are disconnected and the harnesses are open circuited. • Check if the conductor pattern on the LGC board is short circuited or open circuited. • Replace the ADU motor. • Replace the LGC board. • Replace the ADU board. 4 Rollers in the ADU • Check the rollers in the ADU. Replace them if they are worn out.

Code: E120

Description: Bypass misfeeding (Paper not reaching the 1st transport sensor): The paper fed from the bypass tray does not reach the 1st transport sensor.
Causes: 1st transport sensor LGC board Bypass feed clutch Bypass paper sensor Bypass feed roller Bypass separation roller
Remedy: 1 Open the Automatic duplexing unit. Is there any paper in front of the 1st transport sensor? Yes Remove the paper. No 2 2 Is the 1st transport sensor working? (Perform the input check in the test mode: FS-03- [ALL]OFF/[9]/[B]) Yes 3 No • Check if the connector of the 1st transport sensor is disconnected. (J661, J659) • Check if the connector CN316 on the LGC board is disconnected. • Check if the connector pins are disconnected and the harnesses are open circuited. • Check if the conductor pattern on the LGC board is short circuited or open circuited. • Replace the 1st transport sensor. • Replace the LGC board. 3 Is the bypass feed clutch working? (Perform the output check in the test mode: 03-204) Is the bypass paper sensor working? (Perform the input check in the test mode: FS-03-[ALL]OFF/ [2]/[E]) Yes 4 No • Check if the connector of the bypass feed clutch and bypass paper sensor are disconnected. (J695, J696, J699) • Check if the connector CN321 on the LGC board is disconnected. • Check if the connector pins are disconnected and the harnesses are open circuited. • Check if the conductor pattern on the LGC board is short circuited or open circuited. • Replace the bypass feed clutch and bypass paper sensor. • Replace the LGC board. 4 Bypass feed roller Separation pad • Check the bypass feed roller and separation roller. Replace them if they are worn out.

Code: E130

Description: 1st drawer misfeeding (Paper not reaching the 1st transport sensor): The paper fed from the 1st drawer does not reach the 1st transport sensor.
Causes: 1st transport sensor. LGC board 1st drawer feed clutch 1st drawer feed roller 1st drawer separation roller 1st drawer pickup roller
Remedy: 1 Open the Automatic duplexing unit. Is there any paper in front of the 1st transport sensor? Yes Remove the paper. No 2 2 Is the 1st transport sensor working? (Perform the input check in the test mode: FS-03- [ALL]OFF/[9]/[B]) Yes 3 No • Check if the connector of the 1st transport sensor is disconnected. (J661, J659) • Check if the connector CN318 on the LGC board is disconnected. • Check if the connector pins are disconnected and the harnesses are open circuited. • Check if the conductor pattern on the LGC board is short circuited or open circuited. • Replace the 1st transport sensor. • Replace the LGC board. 3 Is the 1st drawer feed clutch working? (Perform the output check in the test mode: FS-03- 201) Yes 4 No • Check if the connector of the 1st drawer feed clutch is disconnected. (J666) • Check if the connector CN316 on the LGC board is disconnected. • Check if the connector pins are disconnected and the harnesses are open circuited. • Check if the conductor pattern on the LGC board is short circuited or open circuited. • Replace the 1st drawer feed clutch. • Replace the LGC board. 4 1st drawer feed roller Separation roller Pickup roller • Check the 1st drawer feed roller, separation roller and pickup roller. Replace them if they are worn out.

Code: E140

Description: 2nd drawer misfeeding (Paper not reaching the 2nd transport sensor): The paper fed from the 2nd drawer does not reach the 2nd transport sensor.
Causes: 2nd transport sensor LGC board 2nd drawer feed clutch 2nd drawer feed roller 2nd drawer separation roller 2nd drawer pickup roller
Remedy: 1 Open the feed cover. Is there any paper in front of the 2nd transport sensor? Yes Remove the paper. No 2 2 Is the 2nd transport sensor working? (Perform the input check in the test mode: FS-03- [F3]ON/[4]/[D]) Yes 3 No • Check if the connector of the 2nd transport sensor is disconnected. (J676) • Check if the connector CN318 on the LGC board is disconnected. • Check if the connector pins are disconnected and the harnesses are open circuited. • Check if the conductor pattern on the LGC board is short circuited or open circuited. • Replace the 2nd transport sensor. • Replace the LGC board. 3 Is the 2nd drawer feed clutch working? (Perform the output check in the test mode: FS-03- 202) Yes 4 No • Check if the connector of the 2nd drawer feed clutch is disconnected. • Check if the connector CN316 on the LGC board is disconnected. • Check if the connector pins are disconnected and the harnesses are open circuited. • Check if the conductor pattern on the LGC board is short circuited or open circuited. • Replace the 2nd drawer feed clutch. • Replace the LGC board. 4 2nd drawer feed roller Separation roller Pickup roller • Check the 2nd drawer feed roller, separation roller and pickup roller. Replace them if they are worn out.
Đăng ký nhận bản tin Đăng ký nhận bản tin Đăng ký nhận bản tin Đăng ký nhận bản tin
Đăng ký nhận bản tin
Nhận ưu đãi sớm nhất khi chương trình diễn ra

Đăng ký nhận bản tin

Việc cho phép sử dụng cookie sẽ giúp cải thiện trải nghiệm của bạn trên trang web này. Chính sách cookie