• Code: E220
• Description: Lower drawer transport jam (Paper not reaching the 1st transport sensor): The paper does not reach the 1st transport sensor after it has passed the lower drawer feed sensor.
• Remedy: Open the jam access cover. Is there paper in front of the upper drawer feed sensor? YES Remove the paper. NO Is the upper drawer feed sensor working? (Perform the input check: 03-[FAX]ON/[3]/[H]) NO 1. Check if the connector of the upper drawer feed sensor is disconnected. 2. Check if the connector CN345 on the LGC board is disconnected. 3. Check if the connector pins are disconnected or the harnesses are open-circuited. 4. Check if the conductor pattern on the LGC board is short- or open-circuited. 5. Replace the upper drawer feed sensor. 6. Replace the LGC board. YES Are the lower transport clutches (high/low speed) working? (Perform the output check: 03-203, 205) NO 1. Check if the connectors of the lower transport clutches (high/low speed) are disconnected. 2. Check if the connector CN337 on the LGC board is disconnected. 3. Check if the connector pins are disconnected or the harnesses are open-circuited. 4. Check if the conductor pattern on the LGC board is short- or open-circuited. 5. Replace the lower transport clutches (high/low speed). 6. Replace the LGC board. YES 1. Check the condition of the feed roller, separation roller and pickup roller of each paper source, and replace them if they are worn out. 2. Check the transport roller. Replace it if it is worn out.

• Code: E300
• Description: PFP upper drawer transport jam (Paper not reaching the registration sensor): The paper does not reach the registration sensor after it has passed the 1st transport sensor.
• Remedy: Open the jam access cover. Is there paper in front of the registration sensor? YES Remove the paper. NO Is the registration sensor working? (Perform the input check: 03-[FAX]ON/[9]/[E]) NO 1. Check if the connector of the registration sensor is disconnected. 2. Check if the connector CN345 on the LGC board is disconnected. 3. Check if the connector pins are disconnected or the harnesses are open-circuited. 4. Check if the conductor pattern on the LGC board is short- or open-circuited. 5. Replace the registration sensor. 6. Replace the LGC board. YES Are the upper transport clutches (high/low speed) working? (Perform the output check: 03-439, 440) NO 1. Check if the connectors of the upper transport clutches (high/low speed) are disconnected. 2. Check if the connector CN362 on the LGC board is disconnected. 3. Check if the connector pins are disconnected or the harnesses are open-circuited. 4. Check if the conductor pattern on the LGC board is short- or open-circuited. 5. Replace the upper transport clutches (high/low speed). 6. Replace the LGC board. YES 1. Check the condition of the feed roller, separation roller and pickup roller of each paper source, and replace them if they are worn out. 2. Check the transport roller. Replace it if it is worn out.

• Code: E310
• Description: PFP upper drawer transport jam (Paper not reaching the 1st transport sensor): The paper does not reach the 1st transport sensor after it has passed the 2nd transport sensor.
• Remedy: Open the jam access cover. Is there paper in front of the upper drawer feed sensor? YES Remove the paper. NO Is the upper drawer feed sensor working? (Perform the input check: 03-[FAX]ON/[3]/[H]) NO 1. Check if the connector of the upper drawer feed sensor is disconnected. 2. Check if the connector CN345 on the LGC board is disconnected. 3. Check if the connector pins are disconnected or the harnesses are open-circuited. 4. Check if the conductor pattern on the LGC board is short- or open-circuited. 5. Replace the upper drawer feed sensor. 6. Replace the LGC board. YES Are the lower transport clutches (high/low speed) working? (Perform the output check: 03-203, 205) NO 1. Check if the connectors of the lower transport clutches (high/low speed) are disconnected. 2. Check if the connector CN337 on the LGC board is disconnected. 3. Check if the connector pins are disconnected or the harnesses are open-circuited. 4. Check if the conductor pattern on the LGC board is short- or open-circuited. 5. Replace the lower transport clutches (high/low speed). 6. Replace the LGC board. YES 1. Check the condition of the feed roller, separation roller and pickup roller of each paper source, and replace them if they are worn out. 2. Check the transport roller. Replace it if it is worn out.

• Code: E320
• Description: PFP upper drawer transport jam (Paper not reaching the 2nd transport sensor): The paper does not reach the 2nd transport sensor after it has passed the PFP upper drawer feed sensor.
• Remedy: Open the side cover. Is there paper in front of the lower drawer feed sensor? YES Remove the paper. NO Is the lower drawer feed sensor working? (Perform the input check: 03-[FAX]ON/[3]/[G]) NO 1. Check if the connector of the lower drawer feed sensor is disconnected. 2. Check if the connector CN345 on the LGC board is disconnected. 3. Check if the connector pins are disconnected or the harnesses are open-circuited. 4. Check if the conductor pattern on the LGC board is short- or open-circuited. 5. Replace the lower drawer feed sensor. 6. Replace the LGC board. YES Are the lower transport clutches working? (Perform the output check: 03-203, 205) NO 1. Check if the connectors of the lower transport clutches (high/low speed) are disconnected. 2. Check if the connector CN337 on the LGC board is disconnected. 3. Check if the connector pins are disconnected or the harnesses are open-circuited. 4. Check if the conductor pattern on the LGC board is short- or open-circuited. 5. Replace the lower transport clutches (high/low speed). 6. Replace the LGC board. YES When the paper fed from the PFP: Is the PFP transport clutch working? (Perform the output check: 03-225) NO 1. Check if the connector of the PFP transport clutch is disconnected. 2. Check if any of the connectors CN241, CN242 and CN244 on the PFP board is disconnected. 3. Check if the connector CN332 on the LGC board is disconnected. 4. Check if the connector pins are disconnected or the harnesses are open-circuited. 5. Check if the conductor patterns on the PFP board and LGC board are short- or open- circuited. 6. Replace the PFP transport clutch. 7. Replace the PFP board. 8. Replace the LGC board. YES 1. Check the condition of the feed roller, separation roller and pickup roller of each paper source, and replace them if they are worn out. 2. Check the transport roller. Replace it if it is worn out.

• Code: E330
• Description: PFP lower drawer transport jam (Paper not reaching the registration sensor): The paper does not reach the registration sensor after it has passed the 1st transport sensor.
• Remedy: Open the jam access cover. Is there paper in front of the registration sensor? YES Remove the paper. NO Is the registration sensor working? (Perform the input check: 03-[FAX]ON/[9]/[E]) NO 1. Check if the connector of the registration sensor is disconnected. 2. Check if the connector CN345 on the LGC board is disconnected. 3. Check if the connector pins are disconnected or the harnesses are open-circuited. 4. Check if the conductor pattern on the LGC board is short- or open-circuited. 5. Replace the registration sensor. 6. Replace the LGC board. YES Are the upper transport clutches (high/low speed) working? (Perform the output check: 03-439, 440) NO 1. Check if the connectors of the upper transport clutches (high/low speed) are disconnected. 2. Check if the connector CN362 on the LGC board is disconnected. 3. Check if the connector pins are disconnected or the harnesses are open-circuited. 4. Check if the conductor pattern on the LGC board is short- or open-circuited. 5. Replace the upper transport clutches (high/low speed). 6. Replace the LGC board. YES 1. Check the condition of the feed roller, separation roller and pickup roller of each paper source, and replace them if they are worn out. 2. Check the transport roller. Replace it if it is worn out.

• Code: E340
• Description: PFP lower drawer transport jam (Paper not reaching the 1st transport sensor): The paper does not reach the 1st transport sensor after it has passed the PFP lower drawer feed sensor.
• Remedy: Open the jam access cover. Is there paper in front of the upper drawer feed sensor? YES Remove the paper. NO Is the upper drawer feed sensor working? (Perform the input check: 03-[FAX]ON/[3]/[H]) NO 1. Check if the connector of the upper drawer feed sensor is disconnected. 2. Check if the connector CN345 on the LGC board is disconnected. 3. Check if the connector pins are disconnected or the harnesses are open-circuited. 4. Check if the conductor pattern on the LGC board is short- or open-circuited. 5. Replace the upper drawer feed sensor. 6. Replace the LGC board. YES Are the lower transport clutches (high/low speed) working? (Perform the output check: 03-203, 205) NO 1. Check if the connectors of the lower transport clutches (high/low speed) are disconnected. 2. Check if the connector CN337 on the LGC board is disconnected. 3. Check if the connector pins are disconnected or the harnesses are open-circuited. 4. Check if the conductor pattern on the LGC board is short- or open-circuited. 5. Replace the lower transport clutches (high/low speed). 6. Replace the LGC board. YES 1. Check the condition of the feed roller, separation roller and pickup roller of each paper source, and replace them if they are worn out. 2. Check the transport roller. Replace it if it is worn out.

• Code: E350
• Description: PFP lower drawer transport jam (Paper not reaching the 2nd transport sensor): The paper does not reach the 2nd transport sensor after it has passed the PFP upper drawer feed sensor.
• Remedy: Open the side cover. Is there paper in front of the lower drawer feed sensor? YES Remove the paper. NO Is the lower drawer feed sensor working? (Perform the input check: 03-[FAX]ON/[3]/[G]) NO 1. Check if the connector of the lower drawer feed sensor is disconnected. 2. Check if the connector CN345 on the LGC board is disconnected. 3. Check if the connector pins are disconnected or the harnesses are open-circuited. 4. Check if the conductor pattern on the LGC board is short- or open-circuited. 5. Replace the lower drawer feed sensor. 6. Replace the LGC board. YES Are the lower transport clutches working? (Perform the output check: 03-203, 205) NO 1. Check if the connectors of the lower transport clutches (high/low speed) are disconnected. 2. Check if the connector CN337 on the LGC board is disconnected. 3. Check if the connector pins are disconnected or the harnesses are open-circuited. 4. Check if the conductor pattern on the LGC board is short- or open-circuited. 5. Replace the lower transport clutches (high/low speed). 6. Replace the LGC board. YES When the paper fed from the PFP: Is the PFP transport clutch working? (Perform the output check: 03-225) NO 1. Check if the connector of the PFP transport clutch is disconnected. 2. Check if any of the connectors CN241, CN242 and CN244 on the PFP board is disconnected. 3. Check if the connector CN332 on the LGC board is disconnected. 4. Check if the connector pins are disconnected or the harnesses are open-circuited. 5. Check if the conductor patterns on the PFP board and LGC board are short- or open- circuited. 6. Replace the PFP transport clutch. 7. Replace the PFP board. 8. Replace the LGC board. YES 1. Check the condition of the feed roller, separation roller and pickup roller of each paper source, and replace them if they are worn out. 2. Check the transport roller. Replace it if it is worn out.

• Code: E360
• Description: PFP lower drawer transport jam (Paper not reaching the PFP upper drawer feed sensor): The paper does not reach the PFP upper drawer feed sensor after it has passed the PFP lower drawer feed sensor.
• Remedy: Open the PFP side cover. Is there any paper in front of the PFP upper drawer feed sensor? YES Remove the paper. NO Is the PFP upper feed sensor working? (Perform the input check: 03-[FAX]OFF/[2]/[D]) NO 1. Check if the connector of the PFP upper drawer feed sensor is disconnected. 2. Check if either of the connectors CN241 or CN243 on the PFP board is disconnected. 3. Check if the connector CN332 on the LGC board is disconnected. 4. Check if the connector pins are disconnected or the harnesses are open-circuited. 5. Check if the conductor patterns on the PFP board and LGC board are short- or open-circuited. 6. Replace the PFP upper drawer feed sensor. 7. Replace the PFP board. 8. Replace the LGC board. YES Is the PFP transport clutch working? (Perform the output check: 03-225) NO 1. Check if the connector of the PFP transport clutch is disconnected. 2. Check if any of the connectors CN241, CN242 and CN244 on the PFP board is disconnected. 3. Check if the connector CN332 on the LGC board is disconnected. 4. Check if the connector pins are disconnected or the harnesses are open-circuited. 5. Check if the conductor patterns on the PFP board and LGC board are short- or open- circuited. 6. Replace the PFP transport clutch. 7. Replace the PFP board. 8. Replace the LGC board. YES 1. Check the condition of the feed roller, separation roller and pickup roller of each paper source, and replace them if they are worn out. 2. Check the PFP transport roller. Replace it if it is worn out.