• Code: E064
• Description: Incorrect paper size setting for PFP lower drawer: The size of paper in the 4th drawer differs from size setting of the equipment.
• Causes:
• Remedy: If any paper remains in the equipment or drawer, remove it. Match the paper size of the drawer setting and the one in the drawer. * Paper size detection is performed at the first sheet of paper when the drawer is opened or closed, or when the power of the equipment is turned ON.

• Code: E065
• Description: Incorrect paper size setting for bypass tray: The size of paper in the bypass tray differs from size setting of the equipment.
• Causes:
• Remedy: If any paper remains in the equipment or drawer, remove it. Match the paper size of the drawer setting and the one in the drawer. * Paper size detection is performed at the first sheet of paper when the drawer is opened or closed, or when the power of the equipment is turned ON.

• Code: E090
• Description: Image data delay jam: Image data to be printed cannot be prepared.
• Causes: SYS board LGC board HDD Main memory
• Remedy: Other • Remove the paper remained in front of the registration sensor) • Check if the error is cleared by turning the power OFF and then back ON. SYS board • Connector check • Main memory check • Board check LGC board • Connector check • Board check HDD • Connector check • HDD check

• Code: E091
• Description: Motor-ON time-out jam: The equipment does not operate normally because abnormality occurred on an interface between the SYS board and engine firmware.
• Causes: SYS board LGC board HDD
• Remedy: Other • Check if there is any paper in the equipment. Remove it if there is. • If the error still occurs, check the following. Power Check if the error is cleared by turning the power OFF and then back ON. SYS board • Connector check • Board check LGC board • Connector check • Board check HDD • Connector check • HDD check

• Code: E0A0
• Description: Image transport ready time-out jam: Image data to be printed cannot be sent.
• Causes: LGC board
• Remedy: LGC board Connector check

• Code: E110
• Description: ADU misfeeding (Paper not reaching the registration sensor): The paper which has passed through ADU does not reach the registration sensor during duplex printing.
• Causes: Registration sensor DRV board LGC board Rollers in the ADU Clean or replace it.
• Remedy: Paper stop jam at the registration roller position Registration guide Check the registration guide. Replace it if needed. All Registration sensor • Sensor check (Perform the input check: 03- [ALL]OFF/[9]/[A]) • Connector check (J1077, J1114) • Harness check DRV board • Board check • Connector check (CN450, CN451, CN462) • Harness check LGC board • Board check • Connector check (CN361, CN362) • Harness check ADU Check if the connector between the ADU and equipment is connected.

• Code: E120
• Description: Bypass misfeeding (Paper not reaching the bypass feed sensor): Paper fed from the bypass tray does not reach the bypass feed sensor.
• Causes: Bypass feed clutch Feed sensor DRV board
• Remedy: Bypass feed clutch • Clutch check (Perform the output check: 03-204) • Connector check (J1073, CN461, J1109) • Harness check Feed sensor • Sensor check (Perform the input check: 03-[ALL]OFF/[9]/[B]) • Connector check (J1072, CN461, J1109) • Harness check DRV board • Board check • Connector check (CN462, CN450, CN451) • Harness check LGC board • Board check • Connector check (CN361, CN362) • Harness check

• Code: E130
• Description: 1st drawer misfeeding (Paper not reaching the 1st drawer feed sensor): The paper fed from the 1st drawer does not reach the 1st drawer feed sensor.
• Causes: Feed sensor DRV board LGC board 1st drawer feed clutch 1st drawer feed roller Replace it if it is worn out. 1st drawer separation roller Replace it if it is worn out. 1st drawer pickup roller Replace it if it is worn out.
• Remedy: Feed sensor • Sensor check (Perform the input check: 03-[ALL]OFF/[9]/[B]) • Connector check (J1072, CN462, J1109) • Harness check 1st drawer feed clutch • Clutch check (Perform the output check: 03-201) • Connector check (CN391, J1016) • Harness check DRV board • Board check • Connector check (CN462, CN450, CN451) • Harness check LGC board • Board check • Connector check (CN361, CN362) • Harness check