Thương hiệu phân phối chính hãng
Giỏ hàng

Mã lỗi Toshiba e-Studio 5005AC — Trang 19/29

Code: E450

Description: LCF side cover open jam
Causes: LCF side cover opening/ closing switch LCF board PFC board LGC board
Remedy: LCF side cover opening/ closing switch • Is the switch working? (Perform the input check: FS-03-[F1]ON/[9]/[A]) • Connector check (CN7, CN70) • Harness check LCF board • Board check • Connector check (CN7, CN1) • Harness check PFC board • Board check • Connector check (CN452, CN459, J700, CN464) • Harness check LGC board • Board check • Connector check (CN323) • Harness check

Code: E480

Description: Bridge unit front cover open jam
Causes: Bridge unit cover opening/ closing detection sensor LGC board
Remedy: Bridge unit cover opening/ closing detection sensor • Is the sensor working? (Perform the input check: FS-03-[ALL]OFF/[7]/[B]) • Connector check (J607) • Harness check LGC board • Board check • Connector check (CN307) • Harness check

Code: E490

Description: Job separator cover open jam
Causes: JSP cover switch LGC board
Remedy: JSP cover switch • Is the JSP cover switch working? (Perform the input check: FS-03-[ALL]OFF[7]/[B]) • Connector check (CN260, CN261) • Harness check LGC board • Board check • Connector check (CN307, J607) • Harness check

Code: E510

Description: Paper not reaching the ADU entrance sensor jam
Causes: Reverse sensor ADU entrance sensor Reverse motor LGC board PFC board ADU board Reverse roller Upper exit roller
Remedy: Reverse sensor • Sensor check (Perform the input check: FS-03-[ALL]OFF/[9]/[D]) • Connector check (J703, CN421) • Harness check ADU entrance sensor • Sensor check (Perform the input check: FS-03-[ALL]OFF/[9]/[G]) • Connector check (J692, CN421) • Harness check Reverse motor • Motor check (Perform the output check: FS-03-121/171) • Connector check (CN301, J609, J611) • Harness check LGC board • Connector check (CN323, CN301) • Harness check • Board check PFC board • Board check • Connector check (CN450, CN452) • Harness check ADU board • Connector check (CN420, CN421, CN422, J689) • Harness check • Board check Reverse roller Roller check (attrition, deformation, deterioration) Upper exit roller Roller check (attrition, deformation, deterioration)

Code: E520

Description: Paper stopping in the ADU jam
Causes: ADU entrance sensor ADU motor LGC board PFC board ADU board Rollers in the ADU Replace it if it is worn out. Pressure spring
Remedy: ADU entrance sensor • Sensor check (Perform the input check: FS-03-[ALL]OFF/[9]/[H]) • Connector check (J693, CN421) • Harness check LGC board • Board check • Connector check (CN323) • Harness check PFC board • Board check • Connector check (CN450, CN452) • Harness check ADU board • Board check • Connector check (J689, CN420, CN421, CN422) • Harness check ADU motor • Motor check (Perform the output check: FS-03-110/160) • Connector check (J691, CN422) • Harness check • Bracket check

Code: E550

Description: Paper remaining jam on the transport path
Causes: Feed or transport roller possibly causing multiple feeding Sensor in the jamming area Refer to the table below. LGC board
Remedy: 1 Jamming transport path Open the cover of the unit/area whose picture is flashing on the control panel and remove any paper on the transport path. 2 Feed or transport roller possibly causing multiple feeding Check the feed roller. 3 Sensor in the jamming area • Sensor check (Refer to the table below) • Harness check • Connector check 4 LGC board • Harness check • Connector check • Board check Notes: If the jamRegistration area Jam access cover Registration sensor FS-03-[ALL]OFF/[9]/[A] Paper clinging detection sensor FS-03-[ALL]OFF/[9]/[E] Registration pass sensor FS-03-[ALL]OFF/[9]/[F] Feed sensor FS-03-[ALL]OFF/[9]/[B] Exit area Fuser cover Exit sensor FS-03-[ALL]OFF/[9]/[C] ADU ADU ADU entrance sensor FS-03-[ALL]OFF/[9]/[G] ADU exit sensor FS-03-[ALL]OFF/[9]/[H] Bypass feed unit Side cover 2nd drawer feed sensor FS-03-[F3]ON/[4]/[D] LCF LCF side cover LCF transport sensor FS-03-[F1]ON/[9]/[F] PFP PFP side cover PFP upper drawer feed sensor FS-03-[F3]ON/[0]/[C] PFP lower drawer feed sensor FS-03-[F3]ON/[0]/[D] Bridge unit Bridge unit Bridge unit transport sensor-1 (Entrance sensor) FS-03-[ALL]OFF/[0]/[A] Bridge unit transport sensor-2 (Exit sensor) FS-03-[ALL]OFF/[0]/[B] Finisher Finisher door Sensors in the finisher is occurring in the ADU, PFP, or LCF, check the board in each unit.

Code: E551

Description: Paper remaining jam on the transport path (when a service call occurs)
Causes: Feed or transport roller possibly causing multiple feeding Sensor in the jamming area Refer to the table below. LGC board
Remedy: 1 Jamming transport path Open the cover of the unit/area whose picture is flashing on the control panel and remove any paper on the transport path. 2 Sensor in the jamming area • Sensor check (Refer to the table below) • Harness check • Connector check 3 LGC board • Harness check • Connector check • Board check Notes: If the jam is occurring in the ADU, LCF or PFP, check the board in each unit.
Registration area Jam access cover Registration sensor FS-03-[ALL]OFF/[9]/[A] Paper clinging detection sensor FS-03-[ALL]OFF/[9]/[E] Registration pass sensor FS-03-[ALL]OFF/[9]/[F] Feed sensor FS-03-[ALL]OFF/[9]/[B] Exit area Fuser cover Exit sensor FS-03-[ALL]OFF/[9]/[C] ADU ADU ADU entrance sensor FS-03-[ALL]OFF/[9]/[G] ADU exit sensor FS-03-[ALL]OFF/[9]/[H] Bypass feed unit Side cover 2nd drawer feed sensor FS-03-[F3]ON/[4]/[D] LCF LCF side cover LCF transport sensor FS-03-[F1]ON/[9]/[F] PFP PFP side cover PFP upper drawer feed sensor FS-03-[F3]ON/[0]/[C] PFP lower drawer feed sensor FS-03-[F3]ON/[0]/[D] Bridge unit Bridge unit Bridge unit transport sensor-1 (Entrance sensor) FS-03-[ALL]OFF/[0]/[A] Bridge unit transport sensor-2 (Exit sensor) FS-03-[ALL]OFF/[0]/[B] Finisher Finisher door Sensors in the finisher

Code: E552

Description: Paper remaining jam on the transport path (when the cover is closed)
Causes: Feed or transport roller possibly causing multiple feeding Sensor in the jamming area Refer to the table below. LGC board
Remedy: 1 Jamming transport path Open the cover of the unit/area whose picture is flashing on the control panel and remove any paper on the transport path. 2 Sensor in the jamming area • Sensor check (Refer to the table below) • Harness check • Connector check 3 LGC board • Harness check • Connector check • Board check Notes: If the jam is occurring in the ADU, LCF or PFP, check the board in each unit.
Registration area Jam access cover Registration sensor FS-03-[ALL]OFF/[9]/[A] Paper clinging detection sensor FS-03-[ALL]OFF/[9]/[E] Registration pass sensor FS-03-[ALL]OFF/[9]/[F] Feed sensor FS-03-[ALL]OFF/[9]/[B] Exit area Fuser cover Exit sensor FS-03-[ALL]OFF/[9]/[C] ADU ADU ADU entrance sensor FS-03-[ALL]OFF/[9]/[G] ADU exit sensor FS-03-[ALL]OFF/[9]/[H] Bypass feed unit Side cover 2nd drawer feed sensor FS-03-[F3]ON/[4]/[D] LCF LCF side cover LCF transport sensor FS-03-[F1]ON/[9]/[F] PFP PFP side cover PFP upper drawer feed sensor FS-03-[F3]ON/[0]/[C] PFP lower drawer feed sensor FS-03-[F3]ON/[0]/[D] Bridge unit Bridge unit Bridge unit transport sensor-1 (Entrance sensor) FS-03-[ALL]OFF/[0]/[A] Bridge unit transport sensor-2 (Exit sensor) FS-03-[ALL]OFF/[0]/[B] Finisher Finisher door Sensors in the finisher
Đăng ký nhận bản tin Đăng ký nhận bản tin Đăng ký nhận bản tin Đăng ký nhận bản tin
Đăng ký nhận bản tin
Nhận ưu đãi sớm nhất khi chương trình diễn ra

Đăng ký nhận bản tin

Việc cho phép sử dụng cookie sẽ giúp cải thiện trải nghiệm của bạn trên trang web này. Chính sách cookie