Description: Paper not reaching the bridge unit transport sensor-1 jam
Causes: Bridge unit transport sensor-1 (entrance sensor) LGC board Bridge unit gate solenoid
Remedy: Paper separation failure at separation guide in the fuser unit Fuser unit • Check the gap between the separation guide and the fuser belt. "6.12.1 Adjustment of the Separation Guide Gap" • Paper tranceport check Drawer Check that paper is not skewed in the side guides of the drawer. Leading edge margin Adjust the margin with FS-05-4402 (Leading edge position adjustment) to "Color: 5.5 mm". Widen the margin if needed. (Specification Black: 4.2 mm / Color: 5 mm) • Use A3/LD paper • It is easy to check skew with a copy of a solid image (about 10 mm on its leading edge). Refer to ") • Connector check (CN307, J607, J801) • Harness check LGC board • Board check • Connector check (CN307) • Harness check Bridge unit • Does the transport roller of the bridge unit work when the fuser motor is rotated? (Perform the output check: FS-03-113/163) • Check the drive system of the equipment and bridge unit. • Check if the rollers in the lower exit roller, the pressure spring and the bridge unit are worn out.
Description: Paper stopping at the bridge unit transport sensor-1 jam
Causes: Bridge unit transport sensor-1 (entrance sensor) LGC board Bridge unit gate solenoid
Remedy: Paper separation failure at separation guide in the fuser unit Fuser unit • Check the gap between the separation guide and the fuser belt. "6.12.1 Adjustment of the Separation Guide Gap" • Paper tranceport check Drawer Check that paper is not skewed in the side guides of the drawer. Leading edge margin Adjust the margin with FS-05-4402 (Leading edge position adjustment) to "Color: 5.5 mm". Widen the margin if needed. (Specification Black: 4.2 mm / Color: 5 mm) • Use A3/LD paper • It is easy to check skew with a copy of a solid image (about 10 mm on its leading edge). Refer to ") • Connector check (CN307, J607, J801) • Harness check LGC board • Board check • Connector check (CN307) • Harness check Bridge unit • Does the transport roller of the bridge unit work when the fuser motor is rotated? (Perform the output check: FS-03-113/163) • Check the drive system of the equipment and bridge unit. • Check if the rollers in the lower exit roller, the pressure spring and the bridge unit are worn out.
Description: Paper not reaching the bridge unit transport sensor-2 jam
Causes: Bridge unit transport sensor-2 (exit sensor) LGC board
Remedy: Bridge unit transport sensor-2 (exit sensor) • Sensor check (Perform the input check: FS-03-[ALL]OFF[0]/[B]) • Connector check (CN307, J607, J802) • Harness check LGC board • Board check • Connector check (CN307) • Harness check Bridge unit • Does the transport roller of the bridge unit work when the fuser motor is rotated? (Perform the output check: FS-03-113/163) • Check the drive system of the equipment and bridge unit. • Check if the rollers in the lower exit roller, the pressure spring and the bridge unit are worn out.
Description: Paper stopping at the bridge unit transport sensor-2 jam
Causes: Bridge unit transport sensor-2 (exit sensor) LGC board
Remedy: Bridge unit transport sensor-2 (exit sensor) • Sensor check (Perform the input check: FS-03-[ALL]OFF[0]/[B]) • Connector check (CN307, J607, J802) • Harness check LGC board • Board check • Connector check (CN307) • Harness check Bridge unit • Does the transport roller of the bridge unit work when the fuser motor is rotated? (Perform the output check: FS-03-113/163) • Check the drive system of the equipment and bridge unit. • Check if the rollers in the lower exit roller, the pressure spring and the bridge unit are worn out.
Nhận ưu đãi sớm nhất khi chương trình diễn ra
Đăng ký nhận bản tin
Việc cho phép sử dụng cookie sẽ giúp cải thiện trải nghiệm của bạn trên trang web này.
Chính sách cookie
Những cookie này là cần thiết để trang web hoạt động đúng cách.
Những cookie này giúp chúng tôi hiểu cách khách truy cập tương tác với trang web.
Những cookie này được sử dụng để cung cấp quảng cáo cá nhân hóa.