Mã lỗi Toshiba e-Studio 500S — Trang 12/24
Code:
Tất cả lỗi (185)
842
843
845.00
848.00
848.01
900
900.90
901
902
903
904
905
906
910
911
912
913
914
917
920.01
920.02
920.03
920.04
920.06
920.07
920.11
920.12
920.13
920.14
920.16
920.17
920.21
920.22
920.23
920.24
920.26
920.27
920.31
920.32
920.33
920.34
920.36
920.37
920.41
920.42
920.43
920.44
920.46
920.47
920.51
920.52
920.53
920.54
920.56
920.57
920.91
920.92
920.93
920.94
920.96
920.97
920.xx
922.02
922.03
922.04
922.06
922.07
922.12
922.13
922.14
922.15
922.16
922.17
922.22
922.23
922.24
922.25
922.26
922.27
922.32
922.33
922.34
922.35
922.36
922.37
922.42
922.43
922.44
922.45
922.46
922.47
922.52
922.53
922.54
922.55
922.56
922.57
922.92
922.93
922.94
922.95
922.96
922.97
923.01
923.11
923.21
923.31
923.41
923.51
923.91
924.01
924.11
924.21
924.31
924.41
924.51
924.91
925.01
925.02
925.11
925.12
925.21
925.22
925.31
925.32
925.41
925.42
925.51
925.52
925.91
925.92
927.00
927.01
927.02
927.03
927.04
927.05
927.06
927.07
929.00
929.66
929.67
930.00
932.00
933.00
934.00
936.00
936.10
936.11
936.20
936.21
936.30
936.31
936.60
936.61
936.9
936.91
937.4
937.41
937.5
937.51
937.7
937.71
937.80
939.00
940.00
947.00
948.00
949.00
950.00
951.00
952.00
953.00
954.00
955.00
956.00
957.00
958.00
980.00
981.00
982.xx
983.00
984.00
990.00
991.00
Description: After hot roll lamp detection, did not roll over to steady state control in time. Fuser page count between 400,000 and 499,999.
Causes: The control code has been lost.
Remedy: See 922.02
Description: Hot roll did not reach operating temperature in time (new enhanced control). Fuser page count between 400,000 and 499,999.
Causes: • Low wattage or incorrect lamp. • Bad thermistor, circuit, or cabling. • Fuser not receiving sufficient AC power. • Poor supply line voltage.
Remedy: See 922.02
Description: Fuser has taken too long to reach desired temperature after increasing interpage gap. Fuser page count between 400,000 and 499,999.
Causes: • Low wattage or incorrect lamp. • Bad thermistor, circuit, or cabling. • Excessive load on the fuser. • Fuser not receiving sufficient AC power. • Poor supply line voltage.
Remedy: See 922.02
Description: Hot roll took too long to reach the beginning lamp detection temperature. Fuser page count stopped at 500,000 to preserve data.
Causes: • Low wattage or incorrect lamp. • Bad thermistor, circuit, or cabling. • Fuser not receiving sufficient AC power. • Poor supply line voltage.
Remedy: See 922.02
Description: Hot roll reached final lamp detection temperature but took longer than largest time in lookup table. Fuser page count stopped at 500,000 to preserve data.
Causes: • Low wattage or incorrect lamp. • Bad thermistor, circuit, or cabling. • Fuser not receiving sufficient AC power. • Poor supply line voltage.
Remedy: See 922.02
Description: Hot roll timed out in trying to reach the final lamp detection temperature. Fuser page count stopped at 500,000 to preserve data.
Causes: • Low wattage or incorrect lamp. • Bad thermistor, circuit, or cabling. • Fuser not receiving sufficient AC power. • Poor supply line voltage.
Remedy: See 922.02
Description: After hot roll lamp detection, did not roll over to steady state control in time. Fuser page count stopped at 500,000 to preserve data.
Causes: The control code has been lost.
Remedy: See 922.02
Description: Hot roll did not reach operating temperature in time (new enhanced control). Fuser page count stopped at 500,000 to preserve data.
Causes: • Low wattage or incorrect lamp. • Bad thermistor, circuit, or cabling. • Fuser not receiving sufficient AC power. • Poor supply line voltage.
Remedy: See 922.02