Thương hiệu phân phối chính hãng
Giỏ hàng

Mã lỗi Toshiba e-Studio 65 — Trang 7/15

Code: CB8

Description: Backup RAM data is abnormal
Remedy: Does turning the power switch on the main unit OFF then ON again rectify the trouble? Yes END No Replace the finisher controller board.

Code: CB9

Description: Saddle stitcher paper pushing plate motor is abnormal
Remedy: Is the paper press plate home position sensor (PI4S) normal? No Replace the sensor. Yes Is the paper press plate motor (M8S) operating at the fixed timing? Yes Replace the saddle stitcher controller board. No Is the paper press plate drive mechanism normal? No Correct the mechanism. Yes Does replacement of the paper press plate motor (M8S) rectify the problem? No Replace the saddle stitcher controller board. Yes END

Code: CBA

Description: Saddle stitcher front stitcher motor is abnormal
Remedy: Are the front or rear stitcher and receptacles installed properly? No Install them correctly. Yes Are the stitching home position switches (PS4S/PS2S) on the front or rear stitchers normal? No Replace the front or rear stitcher. Yes Is the front or rear stitcher operating at the predetermined timing? No Replace the front or rear stitcher. Yes Check the wiring between the stitcher and saddle stitcher controller board. If it is normal, replace the controller board

Code: CBC

Description: Saddle stitcher alignment motor is abnormal
Remedy: Is the aligning plate home position sensor (PI5S) normal? No Replace the sensor. Yes Is the aligning motor (M5S) operating at the fixed timing? Yes Replace the saddle stitcher controller board. No Is the aligning plate drive mechanism normal? No Correct the mechanism. Yes Does replacement of the aligning motor (M5S) rectify the trouble? No Replace the saddle stitcher controller board. Yes END

Code: CBD

Description: Saddle stitcher guide motor is abnormal
Remedy: Is the guide plate home position sensor (PI13S) normal? No Replace the sensor. Yes Is the guide motor (M3S) operating at the fixed timing? Yes Replace the saddle stitcher controller board. No Is the guide plate drive mechanism normal? No Correct the mechanism. Yes Does replacement of the guide motor (M3S) rectify the trouble? No Replace the saddle stitcher controller board. Yes END

Code: CBE

Description: Saddle stitcher folding motor is abnormal
Remedy: Is the fold motor clock sensor (I4S) normal? No Replace the sensor. Yes Is the fold motor (M2S) operating at the fixed timing? Yes Replace the saddle stitcher controller board. No Is the fold roller drive mechanism normal? No Correct the mechanism. Yes Does replacement of the fold motor (M2S) rectify the trouble? No Replace the saddle stitcher controller board. Yes END

Code: CBF

Description: Saddle stitcher paper positioning plate motor is abnormal
Remedy: Is the paper positioning plate home position sensor (PI7S) normal? No Replace the sensor. Yes Is the paper positioning plate operating at the fixed timing? Yes Replace the saddle stitcher controller board. No Is the paper positioning plate drive mechanism normal? No Correct the mechanism. Yes Does replacement of the paper positioning plate motor (M4S) rectify the trouble? No Replace the saddle stitcher controller board. Yes END

Code: CC0

Description: Sensor connector connection error
Remedy: [Procedure 1] Is the guide home position sensor (P13S) or saddle stitcher controller board connector connected? No Connect the connector. Yes Is there a disconnection between the sensor and the saddle stitcher? No Correct. Yes Is DC5V being supplied from J9-7 on the saddle stitcher control board? No Replace the saddle stitcher controller board. Yes Is J9-8 of the saddle stitcher controller board correctly connected to the ground? No Replace the saddle stitcher controller board. Yes END [Procedure 2] Is the connector of the paper pressing plate home position sensor (P14S) or the connector of the saddle stitcher controller board connected? No Connect the connector. Yes Is the connector between the sensor and the stitcher disconnected? No Correct. Yes Is DC5V from J9-10 of the saddle stitcher controller board supplied? No Replace the saddle stitcher controller board. Yes Is J9-11 of the saddle stitcher controller board correctly connected to the ground? No Replace the saddle stitcher controller board. Yes END [Procedure 3] Is the connector of the paper pressing edge position (P15S) or the saddle stitcher controller board connected? No Connect the connector. Yes Is the connection between the sensor and the saddle stitcher disconnected? No Correct. Yes Is DC5V from J9-13 of the saddle stitcher controller board supplied? No Replace the saddle stitcher controller board. Yes Is J9-4 on the saddle stitcher controller board correctly connected to the ground? No Replace the saddle stitcher controller board. Yes END
Đăng ký nhận bản tin Đăng ký nhận bản tin Đăng ký nhận bản tin Đăng ký nhận bản tin
Đăng ký nhận bản tin
Nhận ưu đãi sớm nhất khi chương trình diễn ra

Đăng ký nhận bản tin

Việc cho phép sử dụng cookie sẽ giúp cải thiện trải nghiệm của bạn trên trang web này. Chính sách cookie