Thương hiệu phân phối chính hãng
Giỏ hàng

Mã lỗi Toshiba e-Studio 6560C — Trang 27/44

Code: E511

Description: ADU misfeeding (Paper not reaching the ADU transport sensor-1)
Causes: Duplexing unit path entrance sensor Reverse motor ADU motor-1 PFC board ADU board Rollers
Remedy: Duplexing unit path entrance sensor • Sensor check (Perform the input check: 03-[SCAN]ON/[3]/[H]) • Connector check (CN491, CN497) • Harness check Reverse motor • Motor check (Perform the output check: 03-132/134) • Connector check (CN537, CN539) • Harness check ADU motor-1 • Motor check (Perform the output check: 03-146) • Connector check (CN491, CN495) • Harness check PFC board • Connector check (CN511, CN515) • Board check ADU board • Connector check (CN537, CN539) • Board check Drive unit, Rollers • Gear check • Roller check

Code: E540

Description: ADU misfeeding (Paper not reaching the ADU feed sensor): Paper does not reach the duplexing unit path exit sensor after it has passed the duplexing unit path entrance sensor.
Causes: Duplexing unit path exit sensor ADU motor-1 ADU motor-2 PFC board ADU board Rollers
Remedy: Duplexing unit path exit sensor • Sensor check (Perform the input check: 03-[SCAN]ON/[3]/[G]) • Connector check • Harness check ADU motor-1 • Motor check (Perform the output check: 03-146) • Connector check • Harness check ADU motor-2 • Motor check (Perform the output check: 03-144) • Connector check • Harness check PFC board • Connector check (CN511, CN515) • Board check ADU board • Connector check (CN491, CN492) • Board check Drive unit, Rollers • Gear check • Roller check

Code: E550

Description: Paper remaining jam on the transport path: The paper is remaining on the transport path when printing is finished (caused by a multiple paper feeding).
Causes: Feed or transport roller possibly causing multiple feeding Sensor in the jamming area Refer to the table below PFC board
Remedy: 1 Jamming transport path Open the cover of the unit/area whose picture is flashing on the control panel and remove any paper on the transport path. 2 Feed or transport roller possibly causing multiple feeding Check the feed roller. 3 Sensor in the jamming area • Sensor check (Refer to the table below) • Harness check • Connector check 4 PFC board • Harness check • Connector check • Board check Notes: If the jam is occurring in the ADU or LCF, check the board in each unit.
Paper path section Duplexing unit Registration sensor 03-[ALL]OFF/[4]/[B] 03-[COPY]ON/[5]/[H] Transfer belt paper clinging detection sensor 03-[ALL]OFF/[9]/[C] 2nd transfer side paper clinging detection sensor 03-[ALL]OFF/[9]/[D] 1st drawer transport sensor 03-[SCAN]ON/[1]/[D] Fuser Duplexing unit Fuser transport sensor 03-[ALL]OFF/[2]/[C] 03-[COPY]ON/[5]/[F] Reverse path sensor 03-[ALL]OFF/[1]/[C] 03-[SCAN]ON/[3]/[E] ADU Duplexing unit Cover Duplexing unit path exit sensor 03-[SCAN]ON/[3]/[G] Duplexing unit path entrance sensor 03-[SCAN]ON/[3]/[H] Bypass unit Duplexing unit Bypass feed sensor 03-[SCAN]ON/[3]/[A] Feeding area (equipment) Paper feed cover 4th drawer transport sensor 03-[SCAN]ON/[1]/[A] 3rd drawer/tandem LCF transport sensor 03-[SCAN]ON/[1]/[B] 2nd drawer transport sensor 03-[SCAN]ON/[1]/[C] LCF LCF side cover Option LCF feed sensor 03-[SCAN]ON/[5]/[E] Bridge unit Front cover Bridge unit path exit sensor 03-[ALL]OFF/[1]/[A] 03-[SCAN]ON/[3]/[C] Bridge unit path entrance sensor 03-[ALL]OFF/[1]/[B] 03-[SCAN]ON/[3]/[D] Reverse sensor 03-[SCAN]ON/[3]/[F] Reverse section stationary jam detection sensor 03-[SCAN]ON/[4]/[A] Upper exit section - Upper paper exit sensor 03-[ALL]OFF/[1]/[E] 03-[COPY]ON/[7]/[A] Lower exit section - Lower paper exit sensor 03-[ALL]OFF/[4]/[C] 03-[COPY]ON/[5]/[G] Reverse section Reverse path cover Reverse section paper transport detection sensor 03-[COPY]ON/[8]/[F]

Code: E570

Description: Jam not reaching the bridge unit.
Causes: Reverse sensor Transport entrance motor Fuser motor DFV board PFC board Rollers
Remedy: Reverse sensor • Sensor check (Perform the input check: 03-[SCAN]ON/[3]/[F]) • Connector check • Harness check Transport entrance motor • Motor check (Perform the output check: 03-130) • Connector check • Harness check Fuser motor • Motor check (Perform the output check: 03-129) • Connector check • Harness check DRV board • Connector check (CN537, CN538, CN539) • Board check PFC board • Connector check (CN514, CN515) • Board check Drive unit, Rollers • Gear check • Roller check

Code: E580

Description: Stop jam at the bridge unit
Causes: Reverse sensor Reverse motor Bridge unit transport exit motor DFV board PFC board Rollers
Remedy: Reverse sensor • Sensor check (Perform the input check: 03-[SCAN]ON/[3]/[F]) • Connector check • Harness check Reverse motor • Motor check (Perform the output check: 03-132/134) • Connector check • Harness check Bridge unit transport exit motor • Motor check (Perform the output check: 03-136) • Connector check • Harness check DRV board • Connector check (CN537, CN538, CN539) • Board check PFC board • Connector check (CN514, CN515) • Board check Drive unit, Rollers • Gear check • Roller check

Code: E590

Description: Jam not reaching the upper paper exit sensor
Causes: Upper paper exit sensor Exit motor PFC board DRV board LGC board
Remedy: Upper paper exit sensor • Sensor check (Perform the input check: 03-[COPY]ON/[7]/[A], 03-[ALL]OFF/[1]/[E]) • Connector check • Harness check Exit motor • Motor check (Perform the output check: 03-142) • Connector check • Harness check PFC board • Connector check (CN515,CN516) • Board check DRV board • Connector check (CN537, CN539, CN540) • Board check Drive unit, Rollers • Gear check • Roller check LGC board • Connector check (CN309) • Board check

Code: E5A0

Description: Stop jam at the upper paper exit sensor
Causes: Upper paper exit sensor exit motor PFC board DRV board LGC board
Remedy: Upper paper exit sensor • Sensor check (Perform the input check: 03-[COPY]ON/[7]/[A], 03-[ALL]OFF/[1]/[E]) • Connector check • Harness check Bridge unit transport exit motor • Motor check (Perform the output check: 03-136) • Connector check • Harness check PFC board • Connector check (CN515,CN516) • Board check DRV board • Connector check (CN537, CN539, CN540) • Board check Drive unit, Rollers • Gear check • Roller check LGC board • Connector check (CN309) • Board check

Code: E712

Description: Jam not reaching the original registration sensor: The original fed from the original feeding tray does not reach the original registration sensor.
Causes: Original registration sensor Original pickup solenoid RADF board Perform the 05-3210 Roller Pickup roller, feed roller, separation roller
Remedy: Original registration sensor • Sensor check (Perform the input check: 03-[FAX]ON/[7]/[H]) • Connector check • Harness check Original pickup solenoid • Motor check (Perform the output check: 03-) • Connector check • Harness check RADF board • Connector check (CN74,CN79) • Board check Drive unit, Rollers • Gear check • Roller check
Đăng ký nhận bản tin Đăng ký nhận bản tin Đăng ký nhận bản tin Đăng ký nhận bản tin
Đăng ký nhận bản tin
Nhận ưu đãi sớm nhất khi chương trình diễn ra

Đăng ký nhận bản tin

Việc cho phép sử dụng cookie sẽ giúp cải thiện trải nghiệm của bạn trên trang web này. Chính sách cookie